This user was created before we tested in containers to ensure isolation between the pg and repo hosts which were then just directories. The downside is that this resulted in a lot of sudos to set the pgbackrest user and to remove files which did not belong to the main test user.
Containers provide isolation without needing separate users so we can now safely remove the pgbackrest user. This allows us to remove most sudos, except where they are explicitly needed in tests.
While we're at it, remove the code that installed the Perl C library (which also required sudo) and simply add the build path to @INC instead.
This is only needed when new code is added to the Perl C library, which is becoming rare as the migration progresses.
Also, the code will vary slightly based on the Perl version used for generation so for normal users it is just noise.
Suggested by Stephen Frost.
Three major changes were required to get this working:
1) Provide the path to pgbackrest in the build directory when running outside a container. Tests in a container will continue to install and run against /usr/bin/pgbackrest.
1) Set a per-test lock path so tests don't conflict on the default /tmp/pgbackrest path. Also set a per-test log-path while we are at it.
2) Use localhost instead of a custom host for TLS test connections. Tests in containers will continue to update /etc/hosts and use the custom host.
Add infrastructure and update harnessCfgLoad*() to get the correct exe and paths loaded for testing.
Since new tests are required to verify that running outside a container works, also rework the tests in Travis CI to provide coverage within a reasonable amount of time. Mainly, break up to doc tests by VM and run an abbreviated unit test suite on co6 and co7.
Scaling allows the starting values to be increased from the command-line without code changes.
Also suppress valgrind and assertions when running performance testing. Optimization is left at -O0 because we should not be depending on compiler optimizations to make our code performant, and it makes profiling more informative.
This analysis never produced anything but false positives (var might be NULL) but took over a minute per test run and added 600MB to the test container.
No new Perl code is being developed, so these tools are just taking up time and making migrations to newer platforms harder. There are only a few Perl tests remaining with full coverage so the coverage tool does not warn of loss of coverage in most cases.
Remove both tools and associated libraries.
The tests and documentation have been using the core storage layer but soon that will depend entirely on the C library, creating a bootstrap problem (i.e. the storage layer will be needed to build the C library).
Create a simplified Posix storage layer to be used by documentation and the parts of the test code that build and execute the actual tests. The actual tests will still use the core storage driver so they can interact with any type of storage.
This was being removed by rsync which forced a full build even when a partial should have been fine. Rewrite the file after the rsync so it is preserved.
This report replaces the lcov report that was generated manually for each release.
The lcov report was overly verbose just to say that we have virtually 100% coverage.
Use autoconf to provide a basic configure script. WITH_BACKTRACE is yet to be migrated to configure and the unit tests still use a custom Makefile.
Each C file must include "build.auto.conf" before all other includes and defines. This is enforced by test.pl for includes, but it won't detect incorrect define ordering.
Update packages to call configure and use standard flags to pass options.
This amends 70c30dfb which disabled test tracing in general.
Instead, only enable test tracing by default for modules that are being unit tested. This saves lots of time but still ensures that test tracing is working and helps with debugging in unit tests.
Also rename the option to --debug-test-trace for a clarity.
Detailed stack traces for low-level functions (e.g. strCat, bufMove) can be very useful for debugging but leaving them on for all tests has become quite burdensome in terms of time. Complex operations like generating JSON on a large KevValue can lead to timeouts even with generous values.
Add a new param, --debug-trace, to enable test-level stack trace, but leave it off by default.
The report HTML generated by lcov is overly verbose and cumbersome to navigate. Since we maintain 100% coverage it's far more interesting to look at what is not covered than what is.
The new report presents all missing coverage on a single page and excludes code that is covered for brevity.
Deleted files are showing up in git ls-files (added 57d78092) but they don't actually exist on disk.
If there is someway to exclude deleted files from ls-files then I can't find it, so just tell rsync to ignore missing files.
Code generation saved files even when they had not changed, which often caused code generation cascades. So, don't save files unless they have changed.
Use rsync to determine which files have changed since the last test run. The manifest of changed files is saved and not removed until all code generation and builds have completed. If an error occurs the work will be redone on the next run.
The eventual goal is to do all the builds from the test/repo directory created by rsync but for now it is only used to track changes.
The contents were already preserved between tests in a single test.pl run but for a separate execution the entire project had to be built from scratch, which was getting slower as we added code.
Save the important build flags in a file so the new execution knows whether the build contents can be reused.
Mounting/unmounting tmpfs on /home/[user]/test takes time, forces at least 3GB of memory to be available for tests, and makes it harder to preserve data between tests.
Instead, move mounting of tmpfs to the Vagrantfile and add it to fstab so it survives reboots.
C or Perl coverage tests can now be run on any VM provided a recent enough version of Devel::Cover or lcov is available.
For now, leave u18 as the only VM to run coverage tests due to some issues with older versions of lcov.
This allows setting the test log level independently from the general test harness setting, but current only works for the C tests. It is useful for seeing log output from functions on the console while a test is running.
Bug Fixes:
* Fix potential buffer overrun in error message handling. (Reported by Lætitia.)
* Fix archive write lock being taken for the synchronous archive-get command. (Reported by Uspen.)
Improvements:
* Embed exported C functions and Perl modules directly into the pgBackRest executable.
* Use time_t instead of __time_t for better portability. (Suggested by Nick Floersch.)
* Print total runtime in milliseconds at command end.
Low-level functions only include stack trace in test builds while higher-level functions ship with stack trace built-in. Stack traces include all parameters passed to the function but production builds only create the parameter list when the log level is set high enough, i.e. debug or trace depending on the function.
* Allow more than one test to provide coverage for the same module.
* Add option to disable valgrind.
* Add option to disabled coverage.
* Add option to disable debug build.
* Add option to disable compiler optimization.
* Add --dev-test mode.
The Perl process was exiting directly when called but that interfered with proper locking for the forked async process. Now Perl returns results to the C process which handles all errors, including signals.
Switch from Devel::Cover because it would not report on branch coverage for reports converted from gcov.
Branch coverage is not complete, so for the time being errors will only be generated when statement coverage is not complete. Coverage of unit tests is not displayed in the report unless they are incomplete for either statement or branch coverage.
