This flag, when used in conjunction with --count or --count-matches,
will print a result for each file searched even if there were zero
matches in that file. This is off by default but can be enabled to make
ripgrep behave more like grep.
This also clarifies some of the defaults for the
grep-printer::SummaryBuilder type.
Closes#1370, Closes#1405
This commit adds support for showing a preview of long lines. While the
default still remains as completely suppressing the entire line, this
new functionality will show the first N graphemes of a matching line,
including the number of matches that are suppressed.
This was unfortunately a fairly invasive change to the printer that
required a bit of refactoring. On the bright side, the single line
and multi-line coloring are now more unified than they were before.
Closes#1078
This commit attempts to surface binary filtering in a slightly more
user friendly way. Namely, before, ripgrep would silently stop
searching a file if it detected a NUL byte, even if it had previously
printed a match. This can lead to the user quite reasonably assuming
that there are no more matches, since a partial search is fairly
unintuitive. (ripgrep has this behavior by default because it really
wants to NOT search binary files at all, just like it doesn't search
gitignored or hidden files.)
With this commit, if a match has already been printed and ripgrep detects
a NUL byte, then it will print a warning message indicating that the search
stopped prematurely.
Moreover, this commit adds a new flag, --binary, which causes ripgrep to
stop filtering binary files, but in a way that still avoids dumping
binary data into terminals. That is, the --binary flag makes ripgrep
behave more like grep's default behavior.
For files explicitly specified in a search, e.g., `rg foo some-file`,
then no binary filtering is applied (just like no gitignore and no
hidden file filtering is applied). Instead, ripgrep behaves as if you
gave the --binary flag for all explicitly given files.
This was a fairly invasive change, and potentially increases the UX
complexity of ripgrep around binary files. (Before, there were two
binary modes, where as now there are three.) However, ripgrep is now a
bit louder with warning messages when binary file detection might
otherwise be hiding potential matches, so hopefully this is a net
improvement.
Finally, the `-uuu` convenience now maps to `--no-ignore --hidden
--binary`, since this is closer to the actualy intent of the
`--unrestricted` flag, i.e., to reduce ripgrep's smart filtering. As a
consequence, `rg -uuu foo` should now search roughly the same number of
bytes as `grep -r foo`, and `rg -uuua foo` should search roughly the
same number of bytes as `grep -ra foo`. (The "roughly" weasel word is
used because grep's and ripgrep's binary file detection might differ
somewhat---perhaps based on buffer sizes---which can impact exactly what
is and isn't searched.)
See the numerous tests in tests/binary.rs for intended behavior.
Fixes#306, Fixes#855
This starts the usage of bstr in the printer. We don't use it too much
yet, but it comes in handy for implementing PrinterPath and lets us push
down some platform specific code into bstr.
This commit improves the CRLF hack to be more robust. In particular, in
addition to rewriting `$` as `(?:\r??$)`, we now strip `\r` from the end
of a match if and only if the regex has an ending line anchor required for
a match. This doesn't quite make the hack 100% correct, but should fix most
use cases in practice. An example of a regex that will still be incorrect
is `foo|bar$`, since the analysis isn't quite sophisticated enough to
determine that a `\r` can be safely stripped from any match. Even if we
fix that, regexes like `foo\r|bar$` still won't be handled correctly. Alas,
more work on this front should really be focused on enabling this in the
regex engine itself.
The specific cause of this bug was that grep-searcher was sneakily
stripping CRLF from matching lines when it really shouldn't have. We remove
that code now, and instead rely on better match semantics provided at a
lower level.
Fixes#1095
This commit fixes a bug where both of the following commands always
reported an error:
rg --files-with-matches foo file
rg --files-without-match foo file
In particular, the printer was erroneously respecting the `path` option
even the the summary kind was `PathWithMatch` or `PathWithoutMatch`. The
documented behavior is that those summary kinds always require a path,
and thus, the `path` option has no effect. We fix this by correcting the
case analysis.
This also fixes a bug where the exit code for `--files-without-match`
was not set correctly. We update the printer's `has_match` method to
report the correct value.
Fixes#1106, Closes#1130
This commit moves a lot of "utility" code from ripgrep core into
grep-cli. Any one of these things might not be worth creating a new
crate, but combining everything together results in a fair number of a
convenience routines that make up a decent sized crate.
There is potentially more we could move into the crate, but much of what
remains in ripgrep core is almost entirely dealing with the number of
flags we support.
In the course of doing moving things to the grep-cli crate, we clean up
a lot of gunk and improve failure modes in a number of cases. In
particular, we've fixed a bug where other processes could deadlock if
they write too much to stderr.
Fixes#990
libripgrep is not any one library, but rather, a collection of libraries
that roughly separate the following key distinct phases in a grep
implementation:
1. Pattern matching (e.g., by a regex engine).
2. Searching a file using a pattern matcher.
3. Printing results.
Ultimately, both (1) and (3) are defined by de-coupled interfaces, of
which there may be multiple implementations. Namely, (1) is satisfied by
the `Matcher` trait in the `grep-matcher` crate and (3) is satisfied by
the `Sink` trait in the `grep2` crate. The searcher (2) ties everything
together and finds results using a matcher and reports those results
using a `Sink` implementation.
Closes#162
