virtualenv/FFmpeg
1
0
Fork 0
mirror of https://github.com/FFmpeg/FFmpeg.git synced 2024-12-18 03:19:31 +02:00
Code Issues Releases Activity
3fba5d4f3c
FFmpeg/libavutil/x86/tx_float.asm

1295 lines
40 KiB
NASM
Raw Normal View History

lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
;******************************************************************************
;* Copyright (c) Lynne
;*
;* This file is part of FFmpeg.
;*
;* FFmpeg is free software; you can redistribute it and/or
;* modify it under the terms of the GNU Lesser General Public
;* License as published by the Free Software Foundation; either
;* version 2.1 of the License, or (at your option) any later version.
;*
;* FFmpeg is distributed in the hope that it will be useful,
;* but WITHOUT ANY WARRANTY; without even the implied warranty of
;* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
;* Lesser General Public License for more details.
;*
;* You should have received a copy of the GNU Lesser General Public
;* License along with FFmpeg; if not, write to the Free Software
;* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
;******************************************************************************
; Open `doc/transforms.md` to see the code upon which the transforms here were
; based upon and compare.
; TODO:
; carry over registers from smaller transforms to save on ~8 loads/stores
; check if vinsertf could be faster than verpm2f128 for duplication
; even faster FFT8 (current one is very #instructions optimized)
; replace some xors with blends + addsubs?
; replace some shuffles with vblends?
; avx512 split-radix
libavutil: include assembly with full path from source root Otherwise nasm writes the full host-specific paths into .o output, which breaks binary reproducibility. Signed-off-by: Alexander Kanavin <alex.kanavin@gmail.com> Signed-off-by: Anton Khirnov <anton@khirnov.net>
2022-01-19 00:06:29 +02:00
%include "libavutil/x86/x86util.asm"
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
%define private_prefix ff_tx
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%if ARCH_X86_64
%define ptr resq
%else
%define ptr resd
%endif
%assign i 16
%rep 14
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
cextern tab_ %+ i %+ _float ; ff_tab_i_float...
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%assign i (i << 1)
%endrep
struc AVTXContext
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
.len: resd 1 ; Length
.inv resd 1 ; Inverse flag
.map: ptr 1 ; Lookup table(s)
.exp: ptr 1 ; Exponentiation factors
.tmp: ptr 1 ; Temporary data
.sub: ptr 1 ; Subcontexts
.fn: ptr 4 ; Subcontext functions
.nb_sub: resd 1 ; Subcontext count
; Everything else is inaccessible
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
endstruc
SECTION_RODATA 32
%define POS 0x00000000
%define NEG 0x80000000
%define M_SQRT1_2 0.707106781186547524401
%define COS16_1 0.92387950420379638671875
%define COS16_3 0.3826834261417388916015625
d8_mult_odd: dd M_SQRT1_2, -M_SQRT1_2, -M_SQRT1_2, M_SQRT1_2, \
M_SQRT1_2, -M_SQRT1_2, -M_SQRT1_2, M_SQRT1_2
s8_mult_odd: dd 1.0, 1.0, -1.0, 1.0, -M_SQRT1_2, -M_SQRT1_2, M_SQRT1_2, M_SQRT1_2
s8_perm_even: dd 1, 3, 0, 2, 1, 3, 2, 0
s8_perm_odd1: dd 3, 3, 1, 1, 1, 1, 3, 3
s8_perm_odd2: dd 1, 2, 0, 3, 1, 0, 0, 1
s16_mult_even: dd 1.0, 1.0, M_SQRT1_2, M_SQRT1_2, 1.0, -1.0, M_SQRT1_2, -M_SQRT1_2
s16_mult_odd1: dd COS16_1, COS16_1, COS16_3, COS16_3, COS16_1, -COS16_1, COS16_3, -COS16_3
s16_mult_odd2: dd COS16_3, -COS16_3, COS16_1, -COS16_1, -COS16_3, -COS16_3, -COS16_1, -COS16_1
s16_perm: dd 0, 1, 2, 3, 1, 0, 3, 2
mask_mmmmpppm: dd NEG, NEG, NEG, NEG, POS, POS, POS, NEG
mask_ppmpmmpm: dd POS, POS, NEG, POS, NEG, NEG, POS, NEG
mask_mppmmpmp: dd NEG, POS, POS, NEG, NEG, POS, NEG, POS
mask_mpmppmpm: dd NEG, POS, NEG, POS, POS, NEG, POS, NEG
mask_pmmppmmp: dd POS, NEG, NEG, POS, POS, NEG, NEG, POS
mask_pmpmpmpm: times 4 dd POS, NEG
SECTION .text
; Load complex values (64 bits) via a lookup table
; %1 - output register
; %2 - GRP of base input memory address
; %3 - GPR of LUT (int32_t indices) address
; %4 - LUT offset
; %5 - temporary GPR (only used if vgather is not used)
; %6 - temporary register (for avx only)
Revert "x86/tx_float: remove vgatherdpd usage" This reverts commit 82a68a8771ca39564f6a74e0f875d6852e7a0c2a. Smarter slow ISA penalties makes gathers still useful. The intention is to use gathers with the final stage of non-ptwo iMDCTs, where they give benefit.
2022-05-21 00:05:58 +02:00
; %7 - temporary register (for avx only, enables vgatherdpd (AVX2) if FMA3 is set)
%macro LOAD64_LUT 5-7
%if %0 > 6 && cpuflag(avx2)
pcmpeqd %6, %6 ; pcmpeqq has a 0.5 throughput on Zen 3, this has 0.25
movapd xmm%7, [%3 + %4] ; float mov since vgatherdpd is a float instruction
vgatherdpd %1, [%2 + xmm%7*8], %6 ; must use separate registers for args
%else
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
mov %5d, [%3 + %4 + 0]
movsd xmm%1, [%2 + %5q*8]
%if mmsize == 32
mov %5d, [%3 + %4 + 8]
movsd xmm%6, [%2 + %5q*8]
%endif
mov %5d, [%3 + %4 + 4]
movhps xmm%1, [%2 + %5q*8]
%if mmsize == 32
mov %5d, [%3 + %4 + 12]
movhps xmm%6, [%2 + %5q*8]
vinsertf128 %1, %1, xmm%6, 1
%endif
Revert "x86/tx_float: remove vgatherdpd usage" This reverts commit 82a68a8771ca39564f6a74e0f875d6852e7a0c2a. Smarter slow ISA penalties makes gathers still useful. The intention is to use gathers with the final stage of non-ptwo iMDCTs, where they give benefit.
2022-05-21 00:05:58 +02:00
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endmacro
; Single 2-point in-place complex FFT (will do 2 transforms at once in AVX mode)
; %1 - coefficients (r0.reim, r1.reim)
; %2 - temporary
%macro FFT2 2
shufps %2, %1, %1, q3322
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps %1, %1, %1, q1100
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
addsubps %1, %1, %2
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps %1, %1, %1, q2031
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endmacro
; Single 4-point in-place complex FFT (will do 2 transforms at once in [AVX] mode)
; %1 - even coefficients (r0.reim, r2.reim, r4.reim, r6.reim)
; %2 - odd coefficients (r1.reim, r3.reim, r5.reim, r7.reim)
; %3 - temporary
%macro FFT4 3
subps %3, %1, %2 ; r1234, [r5678]
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
addps %1, %1, %2 ; t1234, [t5678]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
shufps %2, %1, %3, q1010 ; t12, r12
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps %1, %1, %3, q2332 ; t34, r43
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
subps %3, %2, %1 ; a34, b32
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
addps %2, %2, %1 ; a12, b14
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
shufps %1, %2, %3, q1010 ; a1234 even
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps %2, %2, %3, q2332 ; b1423
shufps %2, %2, %2, q1320 ; b1234 odd
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endmacro
; Single/Dual 8-point in-place complex FFT (will do 2 transforms in [AVX] mode)
; %1 - even coefficients (a0.reim, a2.reim, [b0.reim, b2.reim])
; %2 - even coefficients (a4.reim, a6.reim, [b4.reim, b6.reim])
; %3 - odd coefficients (a1.reim, a3.reim, [b1.reim, b3.reim])
; %4 - odd coefficients (a5.reim, a7.reim, [b5.reim, b7.reim])
; %5 - temporary
; %6 - temporary
%macro FFT8 6
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
addps %5, %1, %3 ; q1-8
addps %6, %2, %4 ; k1-8
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
subps %1, %1, %3 ; r1-8
subps %2, %2, %4 ; j1-8
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
shufps %4, %1, %1, q2323 ; r4343
shufps %3, %5, %6, q3032 ; q34, k14
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
shufps %1, %1, %1, q1010 ; r1212
shufps %5, %5, %6, q1210 ; q12, k32
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
xorps %4, %4, [mask_pmmppmmp] ; r4343 * pmmp
addps %6, %5, %3 ; s12, g12
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
mulps %2, %2, [d8_mult_odd] ; r8 * d8_mult_odd
subps %5, %5, %3 ; s34, g43
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
addps %3, %1, %4 ; z1234
unpcklpd %1, %6, %5 ; s1234
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
shufps %4, %2, %2, q2301 ; j2143
shufps %6, %6, %5, q2332 ; g1234
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
addsubps %2, %2, %4 ; l2143
shufps %5, %2, %2, q0123 ; l3412
addsubps %5, %5, %2 ; t1234
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
subps %2, %1, %6 ; h1234 even
subps %4, %3, %5 ; u1234 odd
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
addps %1, %1, %6 ; w1234 even
addps %3, %3, %5 ; o1234 odd
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endmacro
; Single 8-point in-place complex FFT in 20 instructions
; %1 - even coefficients (r0.reim, r2.reim, r4.reim, r6.reim)
; %2 - odd coefficients (r1.reim, r3.reim, r5.reim, r7.reim)
; %3 - temporary
; %4 - temporary
%macro FFT8_AVX 4
subps %3, %1, %2 ; r1234, r5678
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
addps %1, %1, %2 ; q1234, q5678
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
vpermilps %2, %3, [s8_perm_odd1] ; r4422, r6688
shufps %4, %1, %1, q3322 ; q1122, q5566
movsldup %3, %3 ; r1133, r5577
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps %1, %1, %1, q1100 ; q3344, q7788
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
addsubps %3, %3, %2 ; z1234, z5678
addsubps %1, %1, %4 ; s3142, s7586
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: fix forgotten 2-argument mulps Yasm *really* cannot deal with any omitted arguments at all.
2021-04-24 22:33:42 +02:00
mulps %3, %3, [s8_mult_odd] ; z * s8_mult_odd
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
vpermilps %1, %1, [s8_perm_even] ; s1234, s5687 !
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
shufps %2, %3, %3, q2332 ; junk, z7887
xorps %4, %1, [mask_mmmmpppm] ; e1234, e5687 !
vpermilps %3, %3, [s8_perm_odd2] ; z2314, z6556
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
vperm2f128 %1, %1, %4, 0x03 ; e5687, s1234
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
addsubps %2, %2, %3 ; junk, t5678
subps %1, %1, %4 ; w1234, w5678 even
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
vperm2f128 %2, %2, %2, 0x11 ; t5678, t5678
vperm2f128 %3, %3, %3, 0x00 ; z2314, z2314
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
xorps %2, %2, [mask_ppmpmmpm] ; t * ppmpmmpm
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
addps %2, %3, %2 ; u1234, u5678 odd
%endmacro
; Single 16-point in-place complex FFT
; %1 - even coefficients (r0.reim, r2.reim, r4.reim, r6.reim)
; %2 - even coefficients (r8.reim, r10.reim, r12.reim, r14.reim)
; %3 - odd coefficients (r1.reim, r3.reim, r5.reim, r7.reim)
; %4 - odd coefficients (r9.reim, r11.reim, r13.reim, r15.reim)
; %5, %6 - temporary
; %7, %8 - temporary (optional)
%macro FFT16 6-8
FFT4 %3, %4, %5
%if %0 > 7
FFT8_AVX %1, %2, %6, %7
movaps %8, [mask_mpmppmpm]
movaps %7, [s16_perm]
%define mask %8
%define perm %7
%elif %0 > 6
FFT8_AVX %1, %2, %6, %7
movaps %7, [s16_perm]
%define mask [mask_mpmppmpm]
%define perm %7
%else
FFT8_AVX %1, %2, %6, %5
%define mask [mask_mpmppmpm]
%define perm [s16_perm]
%endif
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
xorps %5, %5, %5 ; 0
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
shufps %6, %4, %4, q2301 ; z12.imre, z13.imre...
shufps %5, %5, %3, q2301 ; 0, 0, z8.imre...
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
mulps %4, %4, [s16_mult_odd1] ; z.reim * costab
xorps %5, %5, [mask_mppmmpmp]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%if cpuflag(fma3)
fmaddps %6, %6, [s16_mult_odd2], %4 ; s[8..15]
addps %5, %3, %5 ; s[0...7]
%else
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
mulps %6, %6, [s16_mult_odd2] ; z.imre * costab
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
addps %5, %3, %5 ; s[0...7]
addps %6, %4, %6 ; s[8..15]
%endif
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
mulps %5, %5, [s16_mult_even] ; s[0...7]*costab
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
xorps %4, %6, mask ; s[8..15]*mpmppmpm
xorps %3, %5, mask ; s[0...7]*mpmppmpm
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
vperm2f128 %4, %4, %4, 0x01 ; s[12..15, 8..11]
vperm2f128 %3, %3, %3, 0x01 ; s[4..7, 0..3]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
addps %6, %6, %4 ; y56, u56, y34, u34
addps %5, %5, %3 ; w56, x56, w34, x34
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
vpermilps %6, %6, perm ; y56, u56, y43, u43
vpermilps %5, %5, perm ; w56, x56, w43, x43
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
subps %4, %2, %6 ; odd part 2
addps %3, %2, %6 ; odd part 1
subps %2, %1, %5 ; even part 2
addps %1, %1, %5 ; even part 1
%undef mask
%undef perm
%endmacro
; Cobmines m0...m8 (tx1[even, even, odd, odd], tx2,3[even], tx2,3[odd]) coeffs
; Uses all 16 of registers.
; Output is slightly permuted such that tx2,3's coefficients are interleaved
; on a 2-point basis (look at `doc/transforms.md`)
%macro SPLIT_RADIX_COMBINE 17
%if %1 && mmsize == 32
vperm2f128 %14, %6, %7, 0x20 ; m2[0], m2[1], m3[0], m3[1] even
vperm2f128 %16, %9, %8, 0x20 ; m2[0], m2[1], m3[0], m3[1] odd
vperm2f128 %15, %6, %7, 0x31 ; m2[2], m2[3], m3[2], m3[3] even
vperm2f128 %17, %9, %8, 0x31 ; m2[2], m2[3], m3[2], m3[3] odd
%endif
shufps %12, %10, %10, q2200 ; cos00224466
shufps %13, %11, %11, q1133 ; wim77553311
movshdup %10, %10 ; cos11335577
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps %11, %11, %11, q0022 ; wim66442200
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%if %1 && mmsize == 32
shufps %6, %14, %14, q2301 ; m2[0].imre, m2[1].imre, m2[2].imre, m2[3].imre even
shufps %8, %16, %16, q2301 ; m2[0].imre, m2[1].imre, m2[2].imre, m2[3].imre odd
shufps %7, %15, %15, q2301 ; m3[0].imre, m3[1].imre, m3[2].imre, m3[3].imre even
shufps %9, %17, %17, q2301 ; m3[0].imre, m3[1].imre, m3[2].imre, m3[3].imre odd
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
mulps %14, %14, %13 ; m2[0123]reim * wim7531 even
mulps %16, %16, %11 ; m2[0123]reim * wim7531 odd
mulps %15, %15, %13 ; m3[0123]reim * wim7531 even
mulps %17, %17, %11 ; m3[0123]reim * wim7531 odd
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%else
mulps %14, %6, %13 ; m2,3[01]reim * wim7531 even
mulps %16, %8, %11 ; m2,3[01]reim * wim7531 odd
mulps %15, %7, %13 ; m2,3[23]reim * wim7531 even
mulps %17, %9, %11 ; m2,3[23]reim * wim7531 odd
; reorder the multiplies to save movs reg, reg in the %if above
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps %6, %6, %6, q2301 ; m2[0].imre, m2[1].imre, m3[0].imre, m3[1].imre even
shufps %8, %8, %8, q2301 ; m2[0].imre, m2[1].imre, m3[0].imre, m3[1].imre odd
shufps %7, %7, %7, q2301 ; m2[2].imre, m2[3].imre, m3[2].imre, m3[3].imre even
shufps %9, %9, %9, q2301 ; m2[2].imre, m2[3].imre, m3[2].imre, m3[3].imre odd
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endif
%if cpuflag(fma3) ; 11 - 5 = 6 instructions saved through FMA!
fmaddsubps %6, %6, %12, %14 ; w[0..8] even
fmaddsubps %8, %8, %10, %16 ; w[0..8] odd
fmsubaddps %7, %7, %12, %15 ; j[0..8] even
fmsubaddps %9, %9, %10, %17 ; j[0..8] odd
movaps %13, [mask_pmpmpmpm] ; "subaddps? pfft, who needs that!"
%else
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
mulps %6, %6, %12 ; m2,3[01]imre * cos0246
mulps %8, %8, %10 ; m2,3[01]imre * cos0246
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
movaps %13, [mask_pmpmpmpm] ; "subaddps? pfft, who needs that!"
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
mulps %7, %7, %12 ; m2,3[23]reim * cos0246
mulps %9, %9, %10 ; m2,3[23]reim * cos0246
addsubps %6, %6, %14 ; w[0..8]
addsubps %8, %8, %16 ; w[0..8]
xorps %15, %15, %13 ; +-m2,3[23]imre * wim7531
xorps %17, %17, %13 ; +-m2,3[23]imre * wim7531
addps %7, %7, %15 ; j[0..8]
addps %9, %9, %17 ; j[0..8]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endif
addps %14, %6, %7 ; t10235476 even
addps %16, %8, %9 ; t10235476 odd
subps %15, %6, %7 ; +-r[0..7] even
subps %17, %8, %9 ; +-r[0..7] odd
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps %14, %14, %14, q2301 ; t[0..7] even
shufps %16, %16, %16, q2301 ; t[0..7] odd
xorps %15, %15, %13 ; r[0..7] even
xorps %17, %17, %13 ; r[0..7] odd
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
subps %6, %2, %14 ; m2,3[01] even
subps %8, %4, %16 ; m2,3[01] odd
subps %7, %3, %15 ; m2,3[23] even
subps %9, %5, %17 ; m2,3[23] odd
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
addps %2, %2, %14 ; m0 even
addps %4, %4, %16 ; m0 odd
addps %3, %3, %15 ; m1 even
addps %5, %5, %17 ; m1 odd
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endmacro
; Same as above, only does one parity at a time, takes 3 temporary registers,
; however, if the twiddles aren't needed after this, the registers they use
; can be used as any of the temporary registers.
%macro SPLIT_RADIX_COMBINE_HALF 10
%if %1
shufps %8, %6, %6, q2200 ; cos00224466
shufps %9, %7, %7, q1133 ; wim77553311
%else
shufps %8, %6, %6, q3311 ; cos11335577
shufps %9, %7, %7, q0022 ; wim66442200
%endif
mulps %10, %4, %9 ; m2,3[01]reim * wim7531 even
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
mulps %9, %9, %5 ; m2,3[23]reim * wim7531 even
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps %4, %4, %4, q2301 ; m2[0].imre, m2[1].imre, m3[0].imre, m3[1].imre even
shufps %5, %5, %5, q2301 ; m2[2].imre, m2[3].imre, m3[2].imre, m3[3].imre even
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%if cpuflag(fma3)
fmaddsubps %4, %4, %8, %10 ; w[0..8] even
fmsubaddps %5, %5, %8, %9 ; j[0..8] even
movaps %10, [mask_pmpmpmpm]
%else
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
mulps %4, %4, %8 ; m2,3[01]imre * cos0246
mulps %5, %5, %8 ; m2,3[23]reim * cos0246
addsubps %4, %4, %10 ; w[0..8]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
movaps %10, [mask_pmpmpmpm]
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
xorps %9, %9, %10 ; +-m2,3[23]imre * wim7531
addps %5, %5, %9 ; j[0..8]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endif
addps %8, %4, %5 ; t10235476
subps %9, %4, %5 ; +-r[0..7]
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps %8, %8, %8, q2301 ; t[0..7]
xorps %9, %9, %10 ; r[0..7]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
subps %4, %2, %8 ; %3,3[01]
subps %5, %3, %9 ; %3,3[23]
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
addps %2, %2, %8 ; m0
addps %3, %3, %9 ; m1
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endmacro
; Same as above, tries REALLY hard to use 2 temporary registers.
%macro SPLIT_RADIX_COMBINE_LITE 9
%if %1
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
shufps %8, %6, %6, q2200 ; cos00224466
shufps %9, %7, %7, q1133 ; wim77553311
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%else
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
shufps %8, %6, %6, q3311 ; cos11335577
shufps %9, %7, %7, q0022 ; wim66442200
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endif
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
mulps %9, %9, %4 ; m2,3[01]reim * wim7531 even
shufps %4, %4, %4, q2301 ; m2[0].imre, m2[1].imre, m3[0].imre, m3[1].imre even
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%if cpuflag(fma3)
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
fmaddsubps %4, %4, %8, %9 ; w[0..8] even
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%else
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
mulps %4, %4, %8 ; m2,3[01]imre * cos0246
addsubps %4, %4, %9 ; w[0..8]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endif
%if %1
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
shufps %9, %7, %7, q1133 ; wim77553311
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%else
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
shufps %9, %7, %7, q0022 ; wim66442200
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endif
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
mulps %9, %9, %5 ; m2,3[23]reim * wim7531 even
shufps %5, %5, %5, q2301 ; m2[2].imre, m2[3].imre, m3[2].imre, m3[3].imre even
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%if cpuflag (fma3)
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
fmsubaddps %5, %5, %8, %9 ; j[0..8] even
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%else
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
mulps %5, %5, %8 ; m2,3[23]reim * cos0246
xorps %9, %9, [mask_pmpmpmpm] ; +-m2,3[23]imre * wim7531
addps %5, %5, %9 ; j[0..8]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endif
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
addps %8, %4, %5 ; t10235476
subps %9, %4, %5 ; +-r[0..7]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
shufps %8, %8, %8, q2301 ; t[0..7]
xorps %9, %9, [mask_pmpmpmpm] ; r[0..7]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
subps %4, %2, %8 ; %3,3[01]
subps %5, %3, %9 ; %3,3[23]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
addps %2, %2, %8 ; m0
addps %3, %3, %9 ; m1
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endmacro
%macro SPLIT_RADIX_COMBINE_64 0
SPLIT_RADIX_COMBINE_LITE 1, m0, m1, tx1_e0, tx2_e0, tw_e, tw_o, tmp1, tmp2
movaps [outq + 0*mmsize], m0
movaps [outq + 4*mmsize], m1
movaps [outq + 8*mmsize], tx1_e0
movaps [outq + 12*mmsize], tx2_e0
SPLIT_RADIX_COMBINE_HALF 0, m2, m3, tx1_o0, tx2_o0, tw_e, tw_o, tmp1, tmp2, m0
movaps [outq + 2*mmsize], m2
movaps [outq + 6*mmsize], m3
movaps [outq + 10*mmsize], tx1_o0
movaps [outq + 14*mmsize], tx2_o0
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
movaps tw_e, [tab_64_float + mmsize]
vperm2f128 tw_o, tw_o, [tab_64_float + 64 - 4*7 - mmsize], 0x23
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
movaps m0, [outq + 1*mmsize]
movaps m1, [outq + 3*mmsize]
movaps m2, [outq + 5*mmsize]
movaps m3, [outq + 7*mmsize]
SPLIT_RADIX_COMBINE 0, m0, m2, m1, m3, tx1_e1, tx2_e1, tx1_o1, tx2_o1, tw_e, tw_o, \
tmp1, tmp2, tx2_o0, tx1_o0, tx2_e0, tx1_e0 ; temporary registers
movaps [outq + 1*mmsize], m0
movaps [outq + 3*mmsize], m1
movaps [outq + 5*mmsize], m2
movaps [outq + 7*mmsize], m3
movaps [outq + 9*mmsize], tx1_e1
movaps [outq + 11*mmsize], tx1_o1
movaps [outq + 13*mmsize], tx2_e1
movaps [outq + 15*mmsize], tx2_o1
%endmacro
; Perform a single even/odd split radix combination with loads and stores
; The _4 indicates this is a quarter of the iterations required to complete a full
; combine loop
; %1 must contain len*2, %2 must contain len*4, %3 must contain len*6
%macro SPLIT_RADIX_LOAD_COMBINE_4 8
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
movaps m8, [rtabq + (%5)*mmsize + %7]
vperm2f128 m9, m9, [itabq - (%5)*mmsize + %8], 0x23
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
movaps m0, [outq + (0 + %4)*mmsize + %6]
movaps m2, [outq + (2 + %4)*mmsize + %6]
movaps m1, [outq + %1 + (0 + %4)*mmsize + %6]
movaps m3, [outq + %1 + (2 + %4)*mmsize + %6]
movaps m4, [outq + %2 + (0 + %4)*mmsize + %6]
movaps m6, [outq + %2 + (2 + %4)*mmsize + %6]
movaps m5, [outq + %3 + (0 + %4)*mmsize + %6]
movaps m7, [outq + %3 + (2 + %4)*mmsize + %6]
SPLIT_RADIX_COMBINE 0, m0, m1, m2, m3, \
m4, m5, m6, m7, \
m8, m9, \
m10, m11, m12, m13, m14, m15
movaps [outq + (0 + %4)*mmsize + %6], m0
movaps [outq + (2 + %4)*mmsize + %6], m2
movaps [outq + %1 + (0 + %4)*mmsize + %6], m1
movaps [outq + %1 + (2 + %4)*mmsize + %6], m3
movaps [outq + %2 + (0 + %4)*mmsize + %6], m4
movaps [outq + %2 + (2 + %4)*mmsize + %6], m6
movaps [outq + %3 + (0 + %4)*mmsize + %6], m5
movaps [outq + %3 + (2 + %4)*mmsize + %6], m7
%endmacro
%macro SPLIT_RADIX_LOAD_COMBINE_FULL 2-5
%if %0 > 2
%define offset_c %3
%else
%define offset_c 0
%endif
%if %0 > 3
%define offset_r %4
%else
%define offset_r 0
%endif
%if %0 > 4
%define offset_i %5
%else
%define offset_i 0
%endif
SPLIT_RADIX_LOAD_COMBINE_4 %1, 2*%1, %2, 0, 0, offset_c, offset_r, offset_i
SPLIT_RADIX_LOAD_COMBINE_4 %1, 2*%1, %2, 1, 1, offset_c, offset_r, offset_i
SPLIT_RADIX_LOAD_COMBINE_4 %1, 2*%1, %2, 4, 2, offset_c, offset_r, offset_i
SPLIT_RADIX_LOAD_COMBINE_4 %1, 2*%1, %2, 5, 3, offset_c, offset_r, offset_i
%endmacro
; Perform a single even/odd split radix combination with loads, deinterleaves and
; stores. The _2 indicates this is a half of the iterations required to complete
; a full combine+deinterleave loop
; %3 must contain len*2, %4 must contain len*4, %5 must contain len*6
%macro SPLIT_RADIX_COMBINE_DEINTERLEAVE_2 6
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
movaps m8, [rtabq + (0 + %2)*mmsize]
vperm2f128 m9, m9, [itabq - (0 + %2)*mmsize], 0x23
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
movaps m0, [outq + (0 + 0 + %1)*mmsize + %6]
movaps m2, [outq + (2 + 0 + %1)*mmsize + %6]
movaps m1, [outq + %3 + (0 + 0 + %1)*mmsize + %6]
movaps m3, [outq + %3 + (2 + 0 + %1)*mmsize + %6]
movaps m4, [outq + %4 + (0 + 0 + %1)*mmsize + %6]
movaps m6, [outq + %4 + (2 + 0 + %1)*mmsize + %6]
movaps m5, [outq + %5 + (0 + 0 + %1)*mmsize + %6]
movaps m7, [outq + %5 + (2 + 0 + %1)*mmsize + %6]
SPLIT_RADIX_COMBINE 0, m0, m1, m2, m3, \
m4, m5, m6, m7, \
m8, m9, \
m10, m11, m12, m13, m14, m15
unpckhpd m10, m0, m2
unpckhpd m11, m1, m3
unpckhpd m12, m4, m6
unpckhpd m13, m5, m7
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
unpcklpd m0, m0, m2
unpcklpd m1, m1, m3
unpcklpd m4, m4, m6
unpcklpd m5, m5, m7
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
vextractf128 [outq + (0 + 0 + %1)*mmsize + %6 + 0], m0, 0
vextractf128 [outq + (0 + 0 + %1)*mmsize + %6 + 16], m10, 0
vextractf128 [outq + %3 + (0 + 0 + %1)*mmsize + %6 + 0], m1, 0
vextractf128 [outq + %3 + (0 + 0 + %1)*mmsize + %6 + 16], m11, 0
vextractf128 [outq + %4 + (0 + 0 + %1)*mmsize + %6 + 0], m4, 0
vextractf128 [outq + %4 + (0 + 0 + %1)*mmsize + %6 + 16], m12, 0
vextractf128 [outq + %5 + (0 + 0 + %1)*mmsize + %6 + 0], m5, 0
vextractf128 [outq + %5 + (0 + 0 + %1)*mmsize + %6 + 16], m13, 0
vperm2f128 m10, m10, m0, 0x13
vperm2f128 m11, m11, m1, 0x13
vperm2f128 m12, m12, m4, 0x13
vperm2f128 m13, m13, m5, 0x13
x86/tx_float: use all arguments on vperm2f and vpermilps and reindent comments Apparently even old nasm isn't required to accept incomplete instructions.
2021-04-24 22:15:41 +02:00
movaps m8, [rtabq + (1 + %2)*mmsize]
vperm2f128 m9, m9, [itabq - (1 + %2)*mmsize], 0x23
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
movaps m0, [outq + (0 + 1 + %1)*mmsize + %6]
movaps m2, [outq + (2 + 1 + %1)*mmsize + %6]
movaps m1, [outq + %3 + (0 + 1 + %1)*mmsize + %6]
movaps m3, [outq + %3 + (2 + 1 + %1)*mmsize + %6]
movaps [outq + (0 + 1 + %1)*mmsize + %6], m10 ; m0 conflict
movaps [outq + %3 + (0 + 1 + %1)*mmsize + %6], m11 ; m1 conflict
movaps m4, [outq + %4 + (0 + 1 + %1)*mmsize + %6]
movaps m6, [outq + %4 + (2 + 1 + %1)*mmsize + %6]
movaps m5, [outq + %5 + (0 + 1 + %1)*mmsize + %6]
movaps m7, [outq + %5 + (2 + 1 + %1)*mmsize + %6]
movaps [outq + %4 + (0 + 1 + %1)*mmsize + %6], m12 ; m4 conflict
movaps [outq + %5 + (0 + 1 + %1)*mmsize + %6], m13 ; m5 conflict
SPLIT_RADIX_COMBINE 0, m0, m1, m2, m3, \
m4, m5, m6, m7, \
m8, m9, \
m10, m11, m12, m13, m14, m15 ; temporary registers
unpcklpd m8, m0, m2
unpcklpd m9, m1, m3
unpcklpd m10, m4, m6
unpcklpd m11, m5, m7
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
unpckhpd m0, m0, m2
unpckhpd m1, m1, m3
unpckhpd m4, m4, m6
unpckhpd m5, m5, m7
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
vextractf128 [outq + (2 + 0 + %1)*mmsize + %6 + 0], m8, 0
vextractf128 [outq + (2 + 0 + %1)*mmsize + %6 + 16], m0, 0
vextractf128 [outq + (2 + 1 + %1)*mmsize + %6 + 0], m8, 1
vextractf128 [outq + (2 + 1 + %1)*mmsize + %6 + 16], m0, 1
vextractf128 [outq + %3 + (2 + 0 + %1)*mmsize + %6 + 0], m9, 0
vextractf128 [outq + %3 + (2 + 0 + %1)*mmsize + %6 + 16], m1, 0
vextractf128 [outq + %3 + (2 + 1 + %1)*mmsize + %6 + 0], m9, 1
vextractf128 [outq + %3 + (2 + 1 + %1)*mmsize + %6 + 16], m1, 1
vextractf128 [outq + %4 + (2 + 0 + %1)*mmsize + %6 + 0], m10, 0
vextractf128 [outq + %4 + (2 + 0 + %1)*mmsize + %6 + 16], m4, 0
vextractf128 [outq + %4 + (2 + 1 + %1)*mmsize + %6 + 0], m10, 1
vextractf128 [outq + %4 + (2 + 1 + %1)*mmsize + %6 + 16], m4, 1
vextractf128 [outq + %5 + (2 + 0 + %1)*mmsize + %6 + 0], m11, 0
vextractf128 [outq + %5 + (2 + 0 + %1)*mmsize + %6 + 16], m5, 0
vextractf128 [outq + %5 + (2 + 1 + %1)*mmsize + %6 + 0], m11, 1
vextractf128 [outq + %5 + (2 + 1 + %1)*mmsize + %6 + 16], m5, 1
%endmacro
%macro SPLIT_RADIX_COMBINE_DEINTERLEAVE_FULL 2-3
%if %0 > 2
%define offset %3
%else
%define offset 0
%endif
SPLIT_RADIX_COMBINE_DEINTERLEAVE_2 0, 0, %1, %1*2, %2, offset
SPLIT_RADIX_COMBINE_DEINTERLEAVE_2 4, 2, %1, %1*2, %2, offset
%endmacro
INIT_XMM sse3
cglobal fft2_float, 4, 4, 2, ctx, out, in, stride
movaps m0, [inq]
FFT2 m0, m1
movaps [outq], m0
RET
%macro FFT4 2
INIT_XMM sse2
cglobal fft4_ %+ %1 %+ _float, 4, 4, 3, ctx, out, in, stride
movaps m0, [inq + 0*mmsize]
movaps m1, [inq + 1*mmsize]
%if %2
shufps m2, m1, m0, q3210
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
shufps m0, m0, m1, q3210
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
movaps m1, m2
%endif
FFT4 m0, m1, m2
unpcklpd m2, m0, m1
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
unpckhpd m0, m0, m1
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
movaps [outq + 0*mmsize], m2
movaps [outq + 1*mmsize], m0
RET
%endmacro
FFT4 fwd, 0
FFT4 inv, 1
x86/tx_float: avoid redefining macros FFT16_FN was used for fft8 and for fft16 afterwards.
2022-02-02 08:50:59 +02:00
%macro FFT8_SSE_FN 2
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
INIT_XMM sse3
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
cglobal fft8_ %+ %1, 4, 4, 6, ctx, out, in, tmp
%if %2
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
mov ctxq, [ctxq + AVTXContext.map]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
LOAD64_LUT m0, inq, ctxq, (mmsize/2)*0, tmpq
LOAD64_LUT m1, inq, ctxq, (mmsize/2)*1, tmpq
LOAD64_LUT m2, inq, ctxq, (mmsize/2)*2, tmpq
LOAD64_LUT m3, inq, ctxq, (mmsize/2)*3, tmpq
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%else
movaps m0, [inq + 0*mmsize]
movaps m1, [inq + 1*mmsize]
movaps m2, [inq + 2*mmsize]
movaps m3, [inq + 3*mmsize]
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
FFT8 m0, m1, m2, m3, m4, m5
unpcklpd m4, m0, m3
unpcklpd m5, m1, m2
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
unpckhpd m0, m0, m3
unpckhpd m1, m1, m2
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
movups [outq + 0*mmsize], m4
movups [outq + 1*mmsize], m0
movups [outq + 2*mmsize], m5
movups [outq + 3*mmsize], m1
RET
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endmacro
x86/tx_float: avoid redefining macros FFT16_FN was used for fft8 and for fft16 afterwards.
2022-02-02 08:50:59 +02:00
FFT8_SSE_FN float, 1
FFT8_SSE_FN ns_float, 0
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: avoid redefining macros FFT16_FN was used for fft8 and for fft16 afterwards.
2022-02-02 08:50:59 +02:00
%macro FFT8_AVX_FN 2
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
INIT_YMM avx
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
cglobal fft8_ %+ %1, 4, 4, 4, ctx, out, in, tmp
%if %2
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
mov ctxq, [ctxq + AVTXContext.map]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
LOAD64_LUT m0, inq, ctxq, (mmsize/2)*0, tmpq, m2
LOAD64_LUT m1, inq, ctxq, (mmsize/2)*1, tmpq, m3
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%else
movaps m0, [inq + 0*mmsize]
movaps m1, [inq + 1*mmsize]
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
FFT8_AVX m0, m1, m2, m3
unpcklpd m2, m0, m1
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
unpckhpd m0, m0, m1
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
; Around 2% faster than 2x vperm2f128 + 2x movapd
vextractf128 [outq + 16*0], m2, 0
vextractf128 [outq + 16*1], m0, 0
vextractf128 [outq + 16*2], m2, 1
vextractf128 [outq + 16*3], m0, 1
RET
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endmacro
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: avoid redefining macros FFT16_FN was used for fft8 and for fft16 afterwards.
2022-02-02 08:50:59 +02:00
FFT8_AVX_FN float, 1
FFT8_AVX_FN ns_float, 0
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%macro FFT16_FN 3
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
INIT_YMM %1
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
cglobal fft16_ %+ %2, 4, 4, 8, ctx, out, in, tmp
%if %3
movaps m0, [inq + 0*mmsize]
movaps m1, [inq + 1*mmsize]
movaps m2, [inq + 2*mmsize]
movaps m3, [inq + 3*mmsize]
%else
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
mov ctxq, [ctxq + AVTXContext.map]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
LOAD64_LUT m0, inq, ctxq, (mmsize/2)*0, tmpq, m4
LOAD64_LUT m1, inq, ctxq, (mmsize/2)*1, tmpq, m5
LOAD64_LUT m2, inq, ctxq, (mmsize/2)*2, tmpq, m6
LOAD64_LUT m3, inq, ctxq, (mmsize/2)*3, tmpq, m7
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
FFT16 m0, m1, m2, m3, m4, m5, m6, m7
unpcklpd m5, m1, m3
unpcklpd m4, m0, m2
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
unpckhpd m1, m1, m3
unpckhpd m0, m0, m2
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
vextractf128 [outq + 16*0], m4, 0
vextractf128 [outq + 16*1], m0, 0
vextractf128 [outq + 16*2], m4, 1
vextractf128 [outq + 16*3], m0, 1
vextractf128 [outq + 16*4], m5, 0
vextractf128 [outq + 16*5], m1, 0
vextractf128 [outq + 16*6], m5, 1
vextractf128 [outq + 16*7], m1, 1
RET
%endmacro
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
FFT16_FN avx, float, 0
FFT16_FN avx, ns_float, 1
FFT16_FN fma3, float, 0
FFT16_FN fma3, ns_float, 1
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%macro FFT32_FN 3
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
INIT_YMM %1
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
cglobal fft32_ %+ %2, 4, 4, 16, ctx, out, in, tmp
%if %3
movaps m4, [inq + 4*mmsize]
movaps m5, [inq + 5*mmsize]
movaps m6, [inq + 6*mmsize]
movaps m7, [inq + 7*mmsize]
%else
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
mov ctxq, [ctxq + AVTXContext.map]
x86/tx_float: improve temporary register allocation for loads On Zen 3: Before: 1484285 decicycles in av_tx (fft), 131072 runs, 0 skips After: 1415243 decicycles in av_tx (fft), 131072 runs, 0 skips
2022-05-21 00:50:09 +02:00
LOAD64_LUT m4, inq, ctxq, (mmsize/2)*4, tmpq, m8, m12
LOAD64_LUT m5, inq, ctxq, (mmsize/2)*5, tmpq, m9, m13
LOAD64_LUT m6, inq, ctxq, (mmsize/2)*6, tmpq, m10, m14
LOAD64_LUT m7, inq, ctxq, (mmsize/2)*7, tmpq, m11, m15
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
FFT8 m4, m5, m6, m7, m8, m9
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%if %3
movaps m0, [inq + 0*mmsize]
movaps m1, [inq + 1*mmsize]
movaps m2, [inq + 2*mmsize]
movaps m3, [inq + 3*mmsize]
%else
x86/tx_float: improve temporary register allocation for loads On Zen 3: Before: 1484285 decicycles in av_tx (fft), 131072 runs, 0 skips After: 1415243 decicycles in av_tx (fft), 131072 runs, 0 skips
2022-05-21 00:50:09 +02:00
LOAD64_LUT m0, inq, ctxq, (mmsize/2)*0, tmpq, m8, m12
LOAD64_LUT m1, inq, ctxq, (mmsize/2)*1, tmpq, m9, m13
LOAD64_LUT m2, inq, ctxq, (mmsize/2)*2, tmpq, m10, m14
LOAD64_LUT m3, inq, ctxq, (mmsize/2)*3, tmpq, m11, m15
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
movaps m8, [tab_32_float]
vperm2f128 m9, m9, [tab_32_float + 4*8 - 4*7], 0x23
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
FFT16 m0, m1, m2, m3, m10, m11, m12, m13
SPLIT_RADIX_COMBINE 1, m0, m1, m2, m3, m4, m5, m6, m7, m8, m9, \
m10, m11, m12, m13, m14, m15 ; temporary registers
unpcklpd m9, m1, m3
unpcklpd m10, m5, m7
unpcklpd m8, m0, m2
unpcklpd m11, m4, m6
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
unpckhpd m1, m1, m3
unpckhpd m5, m5, m7
unpckhpd m0, m0, m2
unpckhpd m4, m4, m6
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
vextractf128 [outq + 16* 0], m8, 0
vextractf128 [outq + 16* 1], m0, 0
vextractf128 [outq + 16* 2], m8, 1
vextractf128 [outq + 16* 3], m0, 1
vextractf128 [outq + 16* 4], m9, 0
vextractf128 [outq + 16* 5], m1, 0
vextractf128 [outq + 16* 6], m9, 1
vextractf128 [outq + 16* 7], m1, 1
vextractf128 [outq + 16* 8], m11, 0
vextractf128 [outq + 16* 9], m4, 0
vextractf128 [outq + 16*10], m11, 1
vextractf128 [outq + 16*11], m4, 1
vextractf128 [outq + 16*12], m10, 0
vextractf128 [outq + 16*13], m5, 0
vextractf128 [outq + 16*14], m10, 1
vextractf128 [outq + 16*15], m5, 1
RET
%endmacro
%if ARCH_X86_64
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
FFT32_FN avx, float, 0
FFT32_FN avx, ns_float, 1
FFT32_FN fma3, float, 0
FFT32_FN fma3, ns_float, 1
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%endif
%macro FFT_SPLIT_RADIX_DEF 1-2
ALIGN 16
.%1 %+ pt:
PUSH lenq
mov lenq, (%1/4)
add outq, (%1*4) - (%1/1)
call .32pt
add outq, (%1*2) - (%1/2) ; the synth loops also increment outq
call .32pt
POP lenq
sub outq, (%1*4) + (%1*2) + (%1/2)
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
lea rtabq, [tab_ %+ %1 %+ _float]
lea itabq, [tab_ %+ %1 %+ _float + %1 - 4*7]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
%if %0 > 1
cmp tgtq, %1
je .deinterleave
mov tmpq, %1
.synth_ %+ %1:
SPLIT_RADIX_LOAD_COMBINE_FULL 2*%1, 6*%1, 0, 0, 0
add outq, 8*mmsize
add rtabq, 4*mmsize
sub itabq, 4*mmsize
sub tmpq, 4*mmsize
jg .synth_ %+ %1
cmp lenq, %1
jg %2 ; can't do math here, nasm doesn't get it
ret
%endif
%endmacro
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%macro FFT_SPLIT_RADIX_FN 3
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
INIT_YMM %1
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
cglobal fft_sr_ %+ %2, 4, 8, 16, 272, lut, out, in, len, tmp, itab, rtab, tgt
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
movsxd lenq, dword [lutq + AVTXContext.len]
mov lutq, [lutq + AVTXContext.map]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
mov tgtq, lenq
; Bottom-most/32-point transform ===============================================
ALIGN 16
.32pt:
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%if %3
movaps m4, [inq + 4*mmsize]
movaps m5, [inq + 5*mmsize]
movaps m6, [inq + 6*mmsize]
movaps m7, [inq + 7*mmsize]
%else
x86/tx_float: improve temporary register allocation for loads On Zen 3: Before: 1484285 decicycles in av_tx (fft), 131072 runs, 0 skips After: 1415243 decicycles in av_tx (fft), 131072 runs, 0 skips
2022-05-21 00:50:09 +02:00
LOAD64_LUT m4, inq, lutq, (mmsize/2)*4, tmpq, m8, m12
LOAD64_LUT m5, inq, lutq, (mmsize/2)*5, tmpq, m9, m13
LOAD64_LUT m6, inq, lutq, (mmsize/2)*6, tmpq, m10, m14
LOAD64_LUT m7, inq, lutq, (mmsize/2)*7, tmpq, m11, m15
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
FFT8 m4, m5, m6, m7, m8, m9
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%if %3
movaps m0, [inq + 0*mmsize]
movaps m1, [inq + 1*mmsize]
movaps m2, [inq + 2*mmsize]
movaps m3, [inq + 3*mmsize]
%else
x86/tx_float: improve temporary register allocation for loads On Zen 3: Before: 1484285 decicycles in av_tx (fft), 131072 runs, 0 skips After: 1415243 decicycles in av_tx (fft), 131072 runs, 0 skips
2022-05-21 00:50:09 +02:00
LOAD64_LUT m0, inq, lutq, (mmsize/2)*0, tmpq, m8, m12
LOAD64_LUT m1, inq, lutq, (mmsize/2)*1, tmpq, m9, m13
LOAD64_LUT m2, inq, lutq, (mmsize/2)*2, tmpq, m10, m14
LOAD64_LUT m3, inq, lutq, (mmsize/2)*3, tmpq, m11, m15
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
movaps m8, [tab_32_float]
vperm2f128 m9, m9, [tab_32_float + 32 - 4*7], 0x23
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
FFT16 m0, m1, m2, m3, m10, m11, m12, m13
SPLIT_RADIX_COMBINE 1, m0, m1, m2, m3, m4, m5, m6, m7, m8, m9, \
m10, m11, m12, m13, m14, m15 ; temporary registers
movaps [outq + 1*mmsize], m1
movaps [outq + 3*mmsize], m3
movaps [outq + 5*mmsize], m5
movaps [outq + 7*mmsize], m7
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%if %3
add inq, 8*mmsize
%else
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
add lutq, (mmsize/2)*8
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
cmp lenq, 32
jg .64pt
movaps [outq + 0*mmsize], m0
movaps [outq + 2*mmsize], m2
movaps [outq + 4*mmsize], m4
movaps [outq + 6*mmsize], m6
ret
; 64-point transform ===========================================================
ALIGN 16
.64pt:
; Helper defines, these make it easier to track what's happening
%define tx1_e0 m4
%define tx1_e1 m5
%define tx1_o0 m6
%define tx1_o1 m7
%define tx2_e0 m8
%define tx2_e1 m9
%define tx2_o0 m10
%define tx2_o1 m11
%define tw_e m12
%define tw_o m13
%define tmp1 m14
%define tmp2 m15
SWAP m4, m1
SWAP m6, m3
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%if %3
movaps tx1_e0, [inq + 0*mmsize]
movaps tx1_e1, [inq + 1*mmsize]
movaps tx1_o0, [inq + 2*mmsize]
movaps tx1_o1, [inq + 3*mmsize]
%else
x86/tx_float: improve temporary register allocation for loads On Zen 3: Before: 1484285 decicycles in av_tx (fft), 131072 runs, 0 skips After: 1415243 decicycles in av_tx (fft), 131072 runs, 0 skips
2022-05-21 00:50:09 +02:00
LOAD64_LUT tx1_e0, inq, lutq, (mmsize/2)*0, tmpq, tw_e, tmp1
LOAD64_LUT tx1_e1, inq, lutq, (mmsize/2)*1, tmpq, tw_o, tmp2
LOAD64_LUT tx1_o0, inq, lutq, (mmsize/2)*2, tmpq, tw_e, tmp1
LOAD64_LUT tx1_o1, inq, lutq, (mmsize/2)*3, tmpq, tw_o, tmp2
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
FFT16 tx1_e0, tx1_e1, tx1_o0, tx1_o1, tw_e, tw_o, tx2_o0, tx2_o1
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%if %3
movaps tx2_e0, [inq + 4*mmsize]
movaps tx2_e1, [inq + 5*mmsize]
movaps tx2_o0, [inq + 6*mmsize]
movaps tx2_o1, [inq + 7*mmsize]
%else
x86/tx_float: improve temporary register allocation for loads On Zen 3: Before: 1484285 decicycles in av_tx (fft), 131072 runs, 0 skips After: 1415243 decicycles in av_tx (fft), 131072 runs, 0 skips
2022-05-21 00:50:09 +02:00
LOAD64_LUT tx2_e0, inq, lutq, (mmsize/2)*4, tmpq, tw_e, tmp1
LOAD64_LUT tx2_e1, inq, lutq, (mmsize/2)*5, tmpq, tw_o, tmp2
LOAD64_LUT tx2_o0, inq, lutq, (mmsize/2)*6, tmpq, tw_e, tmp1
LOAD64_LUT tx2_o1, inq, lutq, (mmsize/2)*7, tmpq, tw_o, tmp2
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
FFT16 tx2_e0, tx2_e1, tx2_o0, tx2_o1, tmp1, tmp2, tw_e, tw_o
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
movaps tw_e, [tab_64_float]
vperm2f128 tw_o, tw_o, [tab_64_float + 64 - 4*7], 0x23
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%if %3
add inq, 8*mmsize
%else
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
add lutq, (mmsize/2)*8
x86/tx_float: add permute-free FFT versions These are used in the PFA transforms and MDCTs.
2022-01-25 23:39:09 +02:00
%endif
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
cmp tgtq, 64
je .deinterleave
SPLIT_RADIX_COMBINE_64
cmp lenq, 64
jg .128pt
ret
; 128-point transform ==========================================================
ALIGN 16
.128pt:
PUSH lenq
mov lenq, 32
add outq, 16*mmsize
call .32pt
add outq, 8*mmsize
call .32pt
POP lenq
sub outq, 24*mmsize
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
lea rtabq, [tab_128_float]
lea itabq, [tab_128_float + 128 - 4*7]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
cmp tgtq, 128
je .deinterleave
SPLIT_RADIX_LOAD_COMBINE_FULL 2*128, 6*128
cmp lenq, 128
jg .256pt
ret
; 256-point transform ==========================================================
ALIGN 16
.256pt:
PUSH lenq
mov lenq, 64
add outq, 32*mmsize
call .32pt
add outq, 16*mmsize
call .32pt
POP lenq
sub outq, 48*mmsize
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
lea rtabq, [tab_256_float]
lea itabq, [tab_256_float + 256 - 4*7]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
cmp tgtq, 256
je .deinterleave
SPLIT_RADIX_LOAD_COMBINE_FULL 2*256, 6*256
SPLIT_RADIX_LOAD_COMBINE_FULL 2*256, 6*256, 8*mmsize, 4*mmsize, -4*mmsize
cmp lenq, 256
jg .512pt
ret
; 512-point transform ==========================================================
ALIGN 16
.512pt:
PUSH lenq
mov lenq, 128
add outq, 64*mmsize
call .32pt
add outq, 32*mmsize
call .32pt
POP lenq
sub outq, 96*mmsize
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
lea rtabq, [tab_512_float]
lea itabq, [tab_512_float + 512 - 4*7]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
cmp tgtq, 512
je .deinterleave
mov tmpq, 4
.synth_512:
SPLIT_RADIX_LOAD_COMBINE_FULL 2*512, 6*512
add outq, 8*mmsize
add rtabq, 4*mmsize
sub itabq, 4*mmsize
sub tmpq, 1
jg .synth_512
cmp lenq, 512
jg .1024pt
ret
; 1024-point transform ==========================================================
ALIGN 16
.1024pt:
PUSH lenq
mov lenq, 256
add outq, 96*mmsize
call .32pt
add outq, 64*mmsize
call .32pt
POP lenq
sub outq, 192*mmsize
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
lea rtabq, [tab_1024_float]
lea itabq, [tab_1024_float + 1024 - 4*7]
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
cmp tgtq, 1024
je .deinterleave
mov tmpq, 8
.synth_1024:
SPLIT_RADIX_LOAD_COMBINE_FULL 2*1024, 6*1024
add outq, 8*mmsize
add rtabq, 4*mmsize
sub itabq, 4*mmsize
sub tmpq, 1
jg .synth_1024
cmp lenq, 1024
jg .2048pt
ret
; 2048 to 131072-point transforms ==============================================
FFT_SPLIT_RADIX_DEF 2048, .4096pt
FFT_SPLIT_RADIX_DEF 4096, .8192pt
FFT_SPLIT_RADIX_DEF 8192, .16384pt
FFT_SPLIT_RADIX_DEF 16384, .32768pt
FFT_SPLIT_RADIX_DEF 32768, .65536pt
FFT_SPLIT_RADIX_DEF 65536, .131072pt
FFT_SPLIT_RADIX_DEF 131072
;===============================================================================
; Final synthesis + deinterleaving code
;===============================================================================
.deinterleave:
cmp lenq, 64
je .64pt_deint
imul tmpq, lenq, 2
lea lutq, [4*lenq + tmpq]
.synth_deinterleave:
SPLIT_RADIX_COMBINE_DEINTERLEAVE_FULL tmpq, lutq
add outq, 8*mmsize
add rtabq, 4*mmsize
sub itabq, 4*mmsize
sub lenq, 4*mmsize
jg .synth_deinterleave
RET
; 64-point deinterleave which only has to load 4 registers =====================
.64pt_deint:
SPLIT_RADIX_COMBINE_LITE 1, m0, m1, tx1_e0, tx2_e0, tw_e, tw_o, tmp1, tmp2
SPLIT_RADIX_COMBINE_HALF 0, m2, m3, tx1_o0, tx2_o0, tw_e, tw_o, tmp1, tmp2, tw_e
unpcklpd tmp1, m0, m2
unpcklpd tmp2, m1, m3
unpcklpd tw_o, tx1_e0, tx1_o0
unpcklpd tw_e, tx2_e0, tx2_o0
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
unpckhpd m0, m0, m2
unpckhpd m1, m1, m3
unpckhpd tx1_e0, tx1_e0, tx1_o0
unpckhpd tx2_e0, tx2_e0, tx2_o0
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
vextractf128 [outq + 0*mmsize + 0], tmp1, 0
vextractf128 [outq + 0*mmsize + 16], m0, 0
vextractf128 [outq + 4*mmsize + 0], tmp2, 0
vextractf128 [outq + 4*mmsize + 16], m1, 0
vextractf128 [outq + 8*mmsize + 0], tw_o, 0
vextractf128 [outq + 8*mmsize + 16], tx1_e0, 0
vextractf128 [outq + 9*mmsize + 0], tw_o, 1
vextractf128 [outq + 9*mmsize + 16], tx1_e0, 1
vperm2f128 tmp1, tmp1, m0, 0x31
vperm2f128 tmp2, tmp2, m1, 0x31
vextractf128 [outq + 12*mmsize + 0], tw_e, 0
vextractf128 [outq + 12*mmsize + 16], tx2_e0, 0
vextractf128 [outq + 13*mmsize + 0], tw_e, 1
vextractf128 [outq + 13*mmsize + 16], tx2_e0, 1
lavu/tx: rewrite internal code as a tree-based codelet constructor This commit rewrites the internal transform code into a constructor that stitches transforms (codelets). This allows for transforms to reuse arbitrary parts of other transforms, and allows transforms to be stacked onto one another (such as a full iMDCT using a half-iMDCT which in turn uses an FFT). It also permits for each step to be individually replaced by assembly or a custom implementation (such as an ASIC).
2022-01-20 08:14:46 +02:00
movaps tw_e, [tab_64_float + mmsize]
vperm2f128 tw_o, tw_o, [tab_64_float + 64 - 4*7 - mmsize], 0x23
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
movaps m0, [outq + 1*mmsize]
movaps m1, [outq + 3*mmsize]
movaps m2, [outq + 5*mmsize]
movaps m3, [outq + 7*mmsize]
movaps [outq + 1*mmsize], tmp1
movaps [outq + 5*mmsize], tmp2
SPLIT_RADIX_COMBINE 0, m0, m2, m1, m3, tx1_e1, tx2_e1, tx1_o1, tx2_o1, tw_e, tw_o, \
tmp1, tmp2, tx2_o0, tx1_o0, tx2_e0, tx1_e0 ; temporary registers
unpcklpd tmp1, m0, m1
unpcklpd tmp2, m2, m3
unpcklpd tw_e, tx1_e1, tx1_o1
unpcklpd tw_o, tx2_e1, tx2_o1
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
unpckhpd m0, m0, m1
unpckhpd m2, m2, m3
unpckhpd tx1_e1, tx1_e1, tx1_o1
unpckhpd tx2_e1, tx2_e1, tx2_o1
lavu/x86: add FFT assembly This commit adds a pure x86 assembly SIMD version of the FFT in libavutil/tx. The design of this pure assembly FFT is pretty unconventional. On the lowest level, instead of splitting the complex numbers into real and imaginary parts, we keep complex numbers together but split them in terms of parity. This saves a number of shuffles in each transform, but more importantly, it splits each transform into two independent paths, which we process using separate registers in parallel. This allows us to keep all units saturated and lets us use all available registers to avoid dependencies. Moreover, it allows us to double the granularity of our per-load permutation, skipping many expensive lookups and allowing us to use just 4 loads per register, rather than 8, or in case FMA3 (and by extension, AVX2), use the vgatherdpd instruction, which is at least as fast as 4 separate loads on old hardware, and quite a bit faster on modern CPUs). Higher up, we go for a bottom-up construction of large transforms, foregoing the traditional per-transform call-return recursion chains. Instead, we always start at the bottom-most basis transform (in this case, a 32-point transform), and continue constructing larger and larger transforms until we return to the top-most transform. This way, we only touch the stack 3 times per a complete target transform: once for the 1/2 length transform and two times for the 1/4 length transform. The combination algorithm we use is a standard Split-Radix algorithm, as used in our C code. Although a version with less operations exists (Steven G. Johnson and Matteo Frigo's "A modified split-radix FFT with fewer arithmetic operations", IEEE Trans. Signal Process. 55 (1), 111–119 (2007), which is the one FFTW uses), it only has 2% less operations and requires at least 4x the binary code (due to it needing 4 different paths to do a single transform). That version also has other issues which prevent it from being implemented with SIMD code as efficiently, which makes it lose the marginal gains it offered, and cannot be performed bottom-up, requiring many recursive call-return chains, whose overhead adds up. We go through a lot of effort to minimize load/stores by keeping as much in registers in between construcring transforms. This saves us around 32 cycles, on paper, but in reality a lot more due to load/store aliasing (a load from a memory location cannot be issued while there's a store pending, and there are only so many (2 for Zen 3) load/store units in a CPU). Also, we interleave coefficients during the last stage to save on a store+load per register. Each of the smallest, basis transforms (4, 8 and 16-point in our case) has been extremely optimized. Our 8-point transform is barely 20 instructions in total, beating our old implementation 8-point transform by 1 instruction. Our 2x8-point transform is 23 instructions, beating our old implementation by 6 instruction and needing 50% less cycles. Our 16-point transform's combination code takes slightly more instructions than our old implementation, but makes up for it by requiring a lot less arithmetic operations. Overall, the transform was optimized for the timings of Zen 3, which at the time of writing has the most IPC from all documented CPUs. Shuffles were preferred over arithmetic operations due to their 1/0.5 latency/throughput. On average, this code is 30% faster than our old libavcodec implementation. It's able to trade blows with the previously-untouchable FFTW on small transforms, and due to its tiny size and better prediction, outdoes FFTW on larger transforms by 11% on the largest currently supported size.
2021-04-10 03:54:22 +02:00
vextractf128 [outq + 2*mmsize + 0], tmp1, 0
vextractf128 [outq + 2*mmsize + 16], m0, 0
vextractf128 [outq + 3*mmsize + 0], tmp1, 1
vextractf128 [outq + 3*mmsize + 16], m0, 1
vextractf128 [outq + 6*mmsize + 0], tmp2, 0
vextractf128 [outq + 6*mmsize + 16], m2, 0
vextractf128 [outq + 7*mmsize + 0], tmp2, 1
vextractf128 [outq + 7*mmsize + 16], m2, 1
vextractf128 [outq + 10*mmsize + 0], tw_e, 0
vextractf128 [outq + 10*mmsize + 16], tx1_e1, 0
vextractf128 [outq + 11*mmsize + 0], tw_e, 1
vextractf128 [outq + 11*mmsize + 16], tx1_e1, 1
vextractf128 [outq + 14*mmsize + 0], tw_o, 0
vextractf128 [outq + 14*mmsize + 16], tx2_e1, 0
vextractf128 [outq + 15*mmsize + 0], tw_o, 1
vextractf128 [outq + 15*mmsize + 16], tx2_e1, 1
RET
%endmacro
%if ARCH_X86_64
x86/tx_float: replace fft_sr_avx with fft_sr_fma3 When the SLOW_GATHER flag was added to the AVX2 version, this made FMA3-features not enabled on Zen CPUs. As FMA3 adds 6-7% across all platforms that support it, in the interest of saving space, this commit removes the AVX version and replaces it with an FMA3 version. The only CPUs affected are Sandy Bridge and Bulldozer, which have AVX support, but no FMA3 support. In the future, if there's a demand for it, a version of the function duplicated for AVX can be added.
2022-05-21 01:39:12 +02:00
FFT_SPLIT_RADIX_FN fma3, float, 0
FFT_SPLIT_RADIX_FN fma3, ns_float, 1
Revert "x86/tx_float: remove vgatherdpd usage" This reverts commit 82a68a8771ca39564f6a74e0f875d6852e7a0c2a. Smarter slow ISA penalties makes gathers still useful. The intention is to use gathers with the final stage of non-ptwo iMDCTs, where they give benefit.
2022-05-21 00:05:58 +02:00
%if HAVE_AVX2_EXTERNAL
FFT_SPLIT_RADIX_FN avx2, float, 0
FFT_SPLIT_RADIX_FN avx2, ns_float, 1
%endif
x86/tx_float: Fixes compilation with old yasm Use three operand format on some instructions, and lea to load effective addresses of tables. Signed-off-by: James Almer <jamrial@gmail.com>
2021-04-24 21:01:04 +02:00
%endif
Reference in New Issue Copy Permalink