FFmpeg/doc/ffmpeg-resampler.texi

\input texinfo @c -*- texinfo -*-

@settitle FFmpeg Resampler Documentation
@titlepage
@center @titlefont{FFmpeg Resampler Documentation}
@end titlepage

@top

@contents

@chapter Description
@c man begin DESCRIPTION

The FFmpeg resampler provides an high-level interface to the
libswresample library audio resampling utilities. In particular it
allows to perform audio resampling, audio channel layout rematrixing,
and convert audio format and packing layout.

@c man end DESCRIPTION

@chapter Resampler Options
@c man begin RESAMPLER OPTIONS

The audio resampler supports the following named options.

Options may be set by specifying -@var{option} @var{value} in the
FFmpeg tools, or by setting the value explicitly in the
@code{SwrContext} options or using the @file{libavutil/opt.h} API for
programmatic use.

@table @option

@item ich, in_channel_count
Set the number of input channels. Default value is 0. Setting this
value is not mandatory if the corresponding channel layout
@option{in_channel_layout} is set.

@item och, out_channel_count
Set the number of output channels. Default value is 0. Setting this
value is not mandatory if the corresponding channel layout
@option{out_channel_layout} is set.

@item uch, used_channel_count
Set the number of used channels. Default value is 0. This option is
only used for special remapping.

@item isr, in_sample_rate
Set the input sample rate. Default value is 0.

@item osr, out_sample_rate
Set the output sample rate. Default value is 0.

@item isf, in_sample_fmt
Specify the input sample format. It is set by default to @code{none}.

@item osf, out_sample_fmt
Specify the output sample format. It is set by default to @code{none}.

@item tsf, internal_sample_fmt
Set the internal sample format. Default value is @code{none}.

@item icl, in_channel_layout
Set the input channel layout.

@item ocl, out_channel_layout
Set the output channel layout.

@item clev, center_mix_level
Set center mix level. It is a value expressed in deciBel, and must be
inclusively included between -32 and +32.

@item slev, surround_mix_level
Set surround mix level. It is a value expressed in deciBel, and must
be inclusively included between -32 and +32.

@item lfe_mix_evel
Set LFE mix level.

@item rmvol, rematrix_volume
Set rematrix volume. Default value is 1.0.

@item flags, swr_flags
Set flags used by the converter. Default value is 0.

It supports the following individual flags:
@table @option
@item res
force resampling
@end table

@item dither_scale
Set the dither scale. Default value is 1.

@item dither_method
Set dither method. Default value is 0.

Supported values:
@table @samp
@item rectangular
select rectangular dither
@item triangular
select triangular dither
@item triangular_hp
select triangular dither with high pass
@end table

@item filter_size
Set resampling filter size, default value is 16.

@item phase_shift
Set resampling phase shift, default value is 10, must be included
between 0 and 30.

@item linear_interp
Use Linear Interpolation if set to 1, default value is 0.

@item cutoff
Set cutoff frequency ratio. Must be a float value between 0 and 1,
default value is 0.8.

@item min_comp
Set minimum difference between timestamps and audio data (in seconds)
below which no timestamp compensation of either kind is applied.
Default value is @code{FLT_MAX}.

@item min_hard_comp
Set minimum difference between timestamps and audio data (in seconds)
to trigger padding/trimming the data. Must be a non-negative double,
default value is 0.1.

@item comp_duration
Set duration (in seconds) over which data is stretched/squeezed to
make it match the timestamps. Must be a non-negative double float
value, default value is 1.0.

@item max_soft_comp
Set maximum factor by which data is stretched/squeezed to make it
match the timestamps. Must be a non-negative double float value,
default value is 0.

@item matrix_encoding
Select matrixed stereo encoding.

It accepts the following values:
@table @samp
@item none
select none
@item dolby
select Dolby
@item dplii
select Dolby Pro Logic II
@end table

Default value is @code{none}.

@item filter_type
Select resampling filter type. This only affects resampling
operations.

It accepts the following values:
@table @samp
@item cubic
select cubic
@item blackman_nuttall
select Blackman Nuttall Windowed Sinc
@item kaiser
select Kaiser Windowed Sinc
@end table

@item kaiser_beta
Set Kaiser Window Beta value. Must be an integer included between 2
and 16, default value is 9.

@end table

@c man end RESAMPLER OPTIONS

@include authors.texi

@ignore

@setfilename ffmpeg-resampler
@settitle FFmpeg Resampler

@c man begin SEEALSO
ffmpeg(1), ffplay(1), ffprobe(1), ffserver(1), libswresample(3)
@c man end

@end ignore

@bye