Allow writing an empty channel mask into the wave format header. Useful
if the input file contains an unknown channel layout.
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
The recent commits change the value slightly. Even though it's
within the threshold it's better to risk as little as possible
especially when different systems, processors, FPUs and compilers
are involved.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
Since TNS was fixed with the recent commits retweak the values
so it's more frequently used.
Still not enabled by default yet, though it's possible that it
will be made enabled by default in the near future.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
This commit was made possible with the earlier commits since the
new quantization method basically means we're working always with
unsigned values. The specifications mention to use compression when
the first 2 bits are identical but they didn't mention if this should
happen before or after the conversion to signed values. Actually
they said nothing about conversion to signed values.
With this commit, coefficient compression usually always happens
which saves a lot of space, especially at extremely low bitrates
and doesn't change the quality at all.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
This finally (and again) gets rid of basically everything the
specifications say about how TNS should be done. The main
problem used to be that a single filter was used for all
coefficients which despite being explicitly recommended by
the specifications usually sounds wrong, therefore it's
a corner case in the current TNS implementation.
This commit also changes the coefficient bit size, as apparently
it's better to use lower precision in case the windows are eight
short. This is apparently what fdk_aac uses, looking at the bit
stream and makes sense. Also the order when 8 SHORT windows happen
is important as 7 was too much and according to PSNR was worse
while 5 is just about correct.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
* commit 'b84675d63aaede8f6944b901250a10456c5477e6':
mmaldec: hack against buffering problems on broken input
Merged-by: Hendrik Leppkes <h.leppkes@gmail.com>
* commit '5788623d29c3e806a7879210986110aced758dc2':
jpeg2000: Split codeblock decoding from the main tile decoding
Merged-by: Hendrik Leppkes <h.leppkes@gmail.com>
* commit 'db53a2306f62f05faa67e6f3c60ee55a9b8e4776':
jpeg2000: Do not warn about known and skippable markers
Merged-by: Hendrik Leppkes <h.leppkes@gmail.com>
* commit '9b5a4a9cce3042558e107ae1ed30d9bf3d867a35':
mmvideo: Make sure the rle does not write over the frame boundaries
Merged-by: Hendrik Leppkes <h.leppkes@gmail.com>
* commit '41ed749fe987e60b0485fa721ad869590651324d':
ogg: Do not try to use the parser if it is not present
Merged-by: Hendrik Leppkes <h.leppkes@gmail.com>
This also drops setting the frame->pts field. This is usually not set by
decoders, so this would be an inconsistency that's at worst a danger to
the API user.
It appears the buffer->dts field is normally not set by the MMAL
decoder, so don't use it. If it's ever going to be set by MMAL, we
don't know whether the value will be what we want.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
The generic code in utils.c sets the AVFrame.pkt_dts field from the
packet it was supposedly decoded. This does not have to be true for a
fully asynchronous decoder like mmaldec. It could be overwritten with an
incorrect value. Even if the decoder doesn't determine the DTS (but sets
it to AV_NOPTS_VALUE), it's impossible to determine a correct value in
utils.c.
Decoders can now be marked with FF_CODEC_CAP_SETS_PKT_DTS, in which case
utils.c won't overwrite the field. The decoders are expected to set this
field (even if they only set it to AV_NOPTS_VALUE).
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
This MMAL feature fills in missing timestamps from the framerate set on
the input port. This is generally unwanted, since libavcodec decoders
merely pass through timestamps without ever "fixing" them. The framerate
is also unknown, and even the timebase doesn't have to be set.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Don't try to do a blocking wait for MMAL output if we haven't even sent
a single real packet, but only flush packets. Obviously we can't expect
to get anything back.
Additionally, don't send a flush packet to MMAL in the same case. It
appears the MMAL decoder will sometimes hang in mmal_vc_port_disable()
(called from ffmmal_close_decoder()), waiting for a reply from the GPU
which never arrives. Either MMAL disallows sending flush packets without
preceding real data, or it's a MMAL bug.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
I can't come up with a nice way to handle this. It's hard to keep the
lock-stepped input/output in this case. You can't predict whether the
MMAL decoder will output a picture (because it's asynchronous), so
you have to assume in general that any packet could produce 0 or 1
frames. You can't continue to write input packets to the decoder,
because then you might get too many output frames, which you can't
get rid of because the lavc decoding API does not allow the decoder
to return an output frame without consuming an input frame (except
when flushing).
The ideal fix is a M:N decoding API (preferably asynchronous), which
would make this code potentially much cleaner. For now, this hack
will do.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Not requiring this can end up producing hilariously broken files
together with -c:s copy (e.g. a webvtt file containing binary subtitle data).
Signed-off-by: Simon Thelen <ffmpeg-dev@c-14.de>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Should fix compilation with mingw-w64 trunk, where ID3D11VideoDecoder is available
but ID3D11VideoContext still isn't.
Signed-off-by: James Almer <jamrial@gmail.com>
If we try to listen on TCP port and ff_listen() fails on
interrupt callback socket (bind) descriptor overwrites and
does not closed at all.
As a result, we can't rebind to the same port.
Reviewed-by: Stephan Holljes <klaxa1337@googlemail.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Makes more sense as users usually set the -cutoff option
to low pass filter the signal. The encoder will still over
shoot slightly when encoding normal coefficients however
that's normal.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
