This is an ABI change in libva2: previously the Intel driver had this
behaviour and it was implemented as a driver quirk, but now it is part
of the specification so all drivers must do it.
The filter supports two inputs and (implicitly) scaling the second input
during composition, unlike the software overlay.
The code has been separated into common interface and qsv overlay
implementation. The common part mainly creates the qsv session and
manages the surface which is nearly the same for all qsv filters.
So the qsvvpp.c/qsvvpp.h API can be used by other QSV vpp filters
to reduce code redundancy.
Usage:
-hwaccel qsv -c:v mpeg2_qsv -r 25 -i in.m2v -hwaccel qsv -c:v h264_qsv
-i in.h264 -filter_complex
"overlay_qsv=eof_action=repeat:x=(W-w)/2:y=(H-h)/2" -b 2M -maxrate 3M
-c:v h264_qsv -y out.h264
Two inputs should have different sizes otherwise one will be completely
covered or you need to scale the second input as follows:
-hwaccel qsv -c:v mpeg2_qsv -r 25 -i in.m2v -hwaccel qsv -c:v h264_qsv
-i in.h264 -filter_complex
"overlay_qsv=w=720:h=576:x=(W-w)/2:y=(H-h)/2" -b 2M -maxrate 3M -c:v
h264_qsv -y out.h264
Signed-off-by: ChaoX A Liu <chaox.a.liu@gmail.com>
Signed-off-by: Zhengxu Huang <zhengxu.maxwell@gmail.com>
Signed-off-by: Andrew Zhang <huazh407@gmail.com>
Change-Id: I5c381febb0af6e2f9622c54ba00490ab99d48297
Signed-off-by: Maxym Dmytrychenko <maxim.d33@gmail.com>
Add common filters of the qsv vpp features including scale,denosie,
deinterlace,frc,crop and procAmp.
Performance will be significantly reduced in the test if using cascade
mode just like qsv framerate + qsv scale + qsv deinterlace + qsv denoise in
separated way no matter in system or video memmory cases.
And the code is so redundant because so much the same just as session and
surface's creation and management.
So we add a common qsv filter.
Usage:
-hwaccel qsv -c:v h264_qsv -r 25 -i in -vf
vpp_qsv=w=iw/2:h=400:deinterlace=1:framerate=60:detail=50:denoise=50
-b 2M -maxrate 3M -c:v h264_qsv -y out.h264
Signed-off-by: ChaoX A Liu <chaox.a.liu@gmail.com>
Signed-off-by: Zhengxu Huang <zhengxu.maxwell@gmail.com>
Signed-off-by: Andrew Zhang <huazh407@gmail.com>
Change-Id: I130392ce722138c209ab658c5f03f0009b6e8024
Signed-off-by: Maxym Dmytrychenko <maxim.d33@gmail.com>
The current qsv deinterlace module does not work at all because MSDK needs user to pass
extra parameters to enable hint functions,such as denoise,deinterlace,composition and so on.
Usage:-hwaccel qsv -r 25 -c:v h264_qsv -i in -vf deinterlace_qsv=bob -b 2M
-maxrate 3M -c:v h264_qsv -y out.h264
Signed-off-by: ChaoX A Liu <chaox.a.liu@gmail.com>
Signed-off-by: Zhengxu Huang <zhengxu.maxwell@gmail.com>
Signed-off-by: Andrew Zhang <huazh407@gmail.com>
Change-Id: I9e7ddcf884f2788c2820f6c98affacfb9d8f3287
Signed-off-by: Maxym Dmytrychenko <maxim.d33@gmail.com>
This is something of a hack. It allocates a new hwframe context for
the target format, then maps it back to the source link and overwrites
the input link hw_frames_ctx so that the previous filter will receive
the frames we want from ff_get_video_buffer(). It may fail if
the previous filter imposes any additional constraints on the frames
it wants to use as output.
In order to work correctly with the i965 driver, this also fixes the
direction of forward/backward references - forward references are
intended to be those from the past to the current frame, not from the
current frame to the future.
This disables everything that was deprecated at least 18 months ago.
Readjust the minimum API version as needed, postponing any
API-incompatible changes until the next bump.
Signed-off-by: Vittorio Giovara <vittorio.giovara@gmail.com>
The Intel proprietary VAAPI driver enforces the restriction that a
buffer must be created inside an existing context, so just ensure
this is always true.
When slice_h is rounded up due to chroma subsampling, there's
a risk that jobnr * slice_h exceeds frame->height.
Prior to a638e9184d, this wasn't an issue for the last slice
of a frame, since slice_end was set to frame->height for the last
slice.
a638e9184d tried to fix the case where other slices than the
last one would exceed frame->height (which can happen where the
number of slices/threads is very large compared to the frame
height).
However, the fix in a638e9184d instead broke other cases,
where slice_h * nb_threads < frame->height. Therefore, make
sure the last slice always ends at frame->height.
CC: libav-stable@libav.org
Signed-off-by: Martin Storsjö <martin@martin.st>
This moves work from the configure to the Make stage where it can
be parallelized and ensures that pkgconfig files are updated when
library versions change.
Bug-Id: 449
libavfilter/af_asyncts.c:212:9: warning: absolute value function 'labs' given an argument of type 'int64_t' (aka 'long long') but has parameter of type 'long' which may cause truncation of value [-Wabsolute-value]
Takes a frame associated with a hardware context as input and maps it
to something else (another hardware frame or normal memory) for other
processing. If the frame to map was originally in the target format
(but mapped to something else), the original frame is output.
Also supports mapping backwards, where only the output has a hardware
context. The link immediately before will be supplied with mapped
hardware frames which it can write directly into, and this filter
then unmaps them back to the actual hardware frames.
Also adds a new flag to mark filters which are aware of hwframes and
will perform this task themselves, and marks all appropriate filters
with this flag.
This is required to allow software-mapped hardware frames to work,
because we need to have the frames context available for any later
mapping operation in the filter graph.
The output from the filter graph should only propagate further to an
encoder if the hardware format actually matches the visible format
(mapped frames are valid here and have an hw_frames_ctx, but this
should not be given to the encoder as its hardware context).
If the input has been decoded from a stream which uses edge cropping
then the whole surface need not be valid. This defines an input
region for the scaler so we only use the active area of the frame.
