This adds common code to query driver support and set appropriate
address/size information for each slice. It only supports rectangular
slices for now, since that is the most common use-case.
Sets the level based on the stream properties if it is not explicitly
set by the user. Also add a tier option to set general_tier_flag, since
that affects the level choice.
This was added in libva 2.1.0 (VAAPI 1.1.0). Use AVCodecContext.qmax,
matching the existing behaviour for qmin, and clean up the defaults so
that we only pass min/max when explicitly set.
Query which modes are supported and select between VBR and CBR based
on that - this removes all of the codec-specific rate control mode
selection code.
Previously there was one fixed choice for each codec (e.g. H.265 -> Main
profile), and using anything else then required an explicit option from
the user. This changes to selecting the profile based on the input format
and the set of profiles actually supported by the driver (e.g. P010 input
will choose Main 10 profile for H.265 if the driver supports it).
The entrypoint and render target format are also chosen dynamically in the
same way, removing those explicit selections from the per-codec code.
In a recent commit the default was changed from 0 (component) to 5
(unspecified), however some standards require using 0. With this option, the
user will be able to do so.
Reviewed-by: Michael Niedermayer <michael@niedermayer.cc>
Signed-off-by: Marton Balint <cus@passwd.hu>
The twoloop coder sounds decent at low bitrates, however at higher bitrates
it sounds worse than the fast coder (which used to be the old twoloop coder
before October 2015) and needs quite a lot more CPU.
Change the default to fast. It has been well tested and has had little changes
over the years so its been confirmed to be quite stable.
Also change its description (not valid for more than a year) and the
documentation.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
Corpus VBR mode is a variant of standard VBR where the complexity
distribution midpoint is passed in rather than calculated for a specific
clip or chunk.
The valid range is [0, 10000]. 0 (default) uses standard VBR.
Signed-off-by: James Zern <jzern@google.com>
* commit '4141a5a240fba44b4b4a1c488c279d7dd8a11ec7':
Use modern avconv syntax for codec selection in documentation and tests
Merged-by: James Almer <jamrial@gmail.com>
Use AVCodecContext.compression_level rather than a private option,
replacing the H.264-specific quality option (which stays only for
compatibility).
This now works with the H.265 encoder in the i965 driver, as well as
the existing cases with the H.264 encoder.
(cherry picked from commit 19388a7200)
cutoff is implemented as an option global to lavc, but supported only
by a few encoders. This fact is now reflected in its documentation. ac3's
support of this option is added for completeness.
Signed-off-by: Moritz Barsnick <barsnick@gmx.net>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Pass the cutoff option from lavc's avcodec_options[] to libmp3lame's
lowpass option, without allowing to adjust its default behavior.
Signed-off-by: Moritz Barsnick <barsnick@gmx.net>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Documents options and behaviour, noting when 'chunks' option will
not be honoured.
Signed-off-by: Tom Butterworth <bangnoise@gmail.com>
Signed-off-by: Martin Vignali <martin.vignali@gmail.com>
Thanks to Mathieu Malaterre <malat@debian.org> for reporting the
Que/Queue typo. (https://bugs.debian.org/839542)
Reviewed-by: Lou Logan <lou@lrcd.com>
Signed-off-by: Andreas Cadhalpun <Andreas.Cadhalpun@googlemail.com>
There is really no need for two aac wrappers, we already have
libfdk-aac which is better. Not to mention that faac doesn't
even support HEv1, or HEv2. It's also under a license which is
unusable for distribution, so it would only be useful to people
who will compile their own ffmpeg, only use it themselves (which
at that point should just use fdk-aac).
Signed-off-by: Josh de Kock <josh@itanimul.li>
The default value of -1 indicates that ffmpeg should determine the channel
mapping automatically, which was the behavior before this commit.
Unless the -mapping_family argument is provided, behavior is unchanged.
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
