the SECOND_LEVEL* flags process and name is too long
extract all of them output to funtions, make code clear
Signed-off-by: Steven Liu <lq@chinaffmpeg.org>
Provides a way to change bandwidth parameter inside DASH manifest after a non-CBR H.264 encoding.
Caller now is able to compute the bitrate by itself, after all packets have been written, and then set that value in AVFormatContext->streams->codecpar->bit_rate before calling av_write_trailer. As a result that value will be set in DASH manifest.
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Ever since the codecpar changes, this has been always printed when
opening a flv file. This is because the codecpar changes made all
streams to be added lazily as read_packet is called.
Public fields were added after the private fields (negating the entire
point of this). New private fields go into AVStreamInternal anyway.
The new marker was set by guessing which fields are supposed to be
private and wshich not. recommended_encoder_configuration is accessed by
ffserver_config.c directly, and is supposed to use the public API.
ffmpeg.c accesses AVStream.cur_dts, even though it's a private field,
but that seems to be an older error.
Allow all struct fields to be accessed directly, as long as they're
public.
Before this change, many fields were "public", but could be accessed via
AVOption only. This meant they were effectively not public, but were
present for documentation purposes, which was incredibly confusing at
best.
MSVC doesn't support the %s time format, and instead of returning an
error the invalid parameter handler is invoked which (by default)
terminates the process.
Reviewed-by：Steven Liu <lq@chinaffmpeg.org>
Signed-off-by: Hendrik Leppkes <h.leppkes@gmail.com>
refer to ticket id: #6170
rename file from temp to origin name after complete current segment
Reviewed-by: Aman Gupta <ffmpeg@tmm1.net>
Signed-off-by: Steven Liu <lq@chinaffmpeg.org>
Signed-off-by: Nicolas Roy-Renaud <nicolas.roy-renaud.1@ens.etsmtl.ca>
Reviewed-by: Paul B Mahol <onemda@gmail.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
This dts value can end up in the list in the absence of durations and is in that
case semantically identical to AV_NOPTS_VALUE. We can alternatively prevent
storing RELATIVE_TS_BASE if there is no duration.
Fixes Ticket3640
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Fixes Ticket 6018
This fixes a regression, and allows playback of files containing mpeg4video that are otherwise
not supported
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
When the http method is not set, the method will use POST for ts,
PUT for m3u8, it is not unify, now set it unify.
This ticket id: #5315
Reviewed-by: Michael Niedermayer <michael@niedermayer.cc>
Reviewed-by: Moritz Barsnick <barsnick@gmx.net>
Signed-off-by: Steven Liu <lq@chinaffmpeg.org>
Skips using temporary files when outputting to a protocol other than
"file", which enables dash to output content over network
protocols. The logic has been copied from the HLS format.
Reviewed-by: Steven Liu <lingjiujianke@gmail.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
This commit optimizes HTTP performance by reducing forward seeks, instead
favoring a read-ahead and discard on the current connection (referred to
as a short seek) for seeks that are within a TCP window's worth of data.
This improves performance because with TCP flow control, a window's worth
of data will be in the local socket buffer already or in-flight from the
sender once congestion control on the sender is fully utilizing the window.
Note: this approach doesn't attempt to differentiate from a newly opened
connection which may not be fully utilizing the window due to congestion
control vs one that is. The receiver can't get at this information, so we
assume worst case; that full window is in use (we did advertise it after all)
and that data could be in-flight
The previous behavior of closing the connection, then opening a new
with a new HTTP range value results in a massive amounts of discarded
and re-sent data when large TCP windows are used. This has been observed
on MacOS/iOS which starts with an initial window of 256KB and grows up to
1MB depending on the bandwidth-product delay.
When seeking within a window's worth of data and we close the connection,
then open a new one within the same window's worth of data, we discard
from the current offset till the end of the window. Then on the new
connection the server ends up re-sending the previous data from new
offset till the end of old window.
Example (assumes full window utilization):
TCP window size: 64KB
Position: 32KB
Forward seek position: 40KB
* (Next window)
32KB |--------------| 96KB |---------------| 160KB
*
40KB |---------------| 104KB
Re-sent amount: 96KB - 40KB = 56KB
For a real world test example, I have MP4 file of ~25MB, which ffplay
only reads ~16MB and performs 177 seeks. With current ffmpeg, this results
in 177 HTTP GETs and ~73MB worth of TCP data communication. With this
patch, ffmpeg issues 4 HTTP GETs and 3 seeks for a total of ~22MB of TCP data
communication.
To support this feature, the short seek logic in avio_seek() has been
extended to call a function to get the short seek threshold value. This
callback has been plumbed to the URLProtocol structure, which now has
infrastructure in HTTP and TCP to get the underlying receiver window size
via SO_RCVBUF. If the underlying URL and protocol don't support returning
a short seek threshold, the default s->short_seek_threshold is used
This feature has been tested on Windows 7 and MacOS/iOS. Windows support
is slightly complicated by the fact that when TCP window auto-tuning is
enabled, SO_RCVBUF doesn't report the real window size, but it does if
SO_RCVBUF was manually set (disabling auto-tuning). So we can only use
this optimization on Windows in the later case
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Reported-by: SleepProgger <security@gnutp.com>
Reviewed-by: Steven Liu <lingjiujianke@gmail.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
hls-encoder currenlty does not provide stream level metadata to mpegts
muxer. This patch fixes track #3848 bug.
Signed-off-by: Bela Bodecs <bodecsb@vivanet.hu>
Signed-off-by: Steven Liu <lq@chinaffmpeg.org>
This enables having multiple tracks of the same type which would
be treated as different things by the media server (as opposed to
different bit rate versions of the same track). According to the
smooth streaming specification, just setting the systemLanguage
tag is not enough to note that a track with the same attributes
differs from another one.
Reviewed-by: Martin
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
