then we can set the rtp read timeout instead of infinite timeout.
How to test(5s timeout):
./ffprobe -i rtp://192.168.1.67:1234?timeout=5000000
Signed-off-by: Limin Wang <lance.lmwang@gmail.com>
remove the timeout option docs part for HTTP protocol and add
auth_type option part.
Reviewed-by: Gyan Doshi <ffmpeg@gyani.pro>
Signed-off-by: Jun Zhao <barryjzhao@tencent.com>
Supports connecting to a RabbitMQ broker via AMQP version 0-9-1.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Signed-off-by: Marton Balint <cus@passwd.hu>
rw_timeout is the generic URLcontext option, not the protocol specific timeout
option, also ?rw_timeout never worked because ?timeout was parsed instead.
Signed-off-by: Marton Balint <cus@passwd.hu>
It is a common mistake that people only increase fifo_size when they experience
drops, unfortunately this does not help for higher bitrate (> 100 Mbps) streams
when the reader thread simply might not receive the packets in time (especially
under high CPU load) if the default 64 KB of kernel buffer size is used.
New default is determined so that common linux systems can set this buffer size
without tuning kernel parameters.
Signed-off-by: Marton Balint <cus@passwd.hu>
add linger parameter to libsrt, it's setting the number of seconds
that the socket waits for unsent data when closing.
Reviewed-by: Andriy Gelman <andriy.gelman@gmail.com>
Signed-off-by: Jun Zhao <barryjzhao@tencent.com>
This introduces two new AVOption options for the FTP protocol,
one named ftp-user to supply the username to be used for auth,
one named ftp-password to supply the password to be used for auth.
These are useful for when an API user does not wish to deal with
URL manipulation and percent encoding.
Setting them while also having credentials in the URL will use the
credentials from the URL. The rationale for this is that credentials
embedded in the URL are probably more specific to what the user is
trying to do than anything set by some API user.
Signed-off-by: Nicolas Frattaroli <ffmpeg@fratti.ch>
Signed-off-by: Marton Balint <cus@passwd.hu>
When ffmpeg was streaming, multiple clients were only supported by using a
multicast destination address. An alternative was to stream to a server which
re-distributes the content. This commit adds ZeroMQ as a protocol, which allows
multiple clients to connect to a single ffmpeg instance.
Signed-off-by: Marton Balint <cus@passwd.hu>
Fix ticket #7297
The current setting for send-expect-100 option is either
enabled if applicable or forced enabled, no option to force
disable the header. This change is to expand the option setting
to provide more flexibility, which is useful for rstp case.
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Several SRT options are missing. Since pkg_config requires libsrt v1.3.0 and above, it should be able to support options added in libsrt v1.3.0 and below.
This commit adds 8 SRT options.
sndbuf, rcvbuf, lossmaxttl, minversion, streamid, smoother, messageapi and transtype
The keys of option are equivalent to stransmit.
https://github.com/Haivision/srt/blob/v1.3.0/apps/socketoptions.hpp#L196-L223
Signed-off-by: Marton Balint <cus@passwd.hu>
This allows getting data only from a specific source IP. This is useful not
only for unicast but for multicast as well because multicast source
subscriptions do not act as source filters for the incoming packets.
Signed-off-by: Marton Balint <cus@passwd.hu>
Also make sure we set the URL context max packet size accordingly.
Based on a patch by Tudor Suciu <tudor.suciu@gmail.com>
Signed-off-by: Marton Balint <cus@passwd.hu>
The protocol requires libsrt (https://github.com/Haivision/srt) to be
installed
Signed-off-by: Sven Dueking <sven.dueking@nablet.com>
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Can be used by the api user to figure out what http features the server supports based on the response received.
Signed-off-by: Aman Gupta <aman@tmm1.net>
This can reduce latency and increase throughput, particularly on high
latency networks.
Signed-off-by: Aman Gupta <aman@tmm1.net>
Reviewed-by: Jeyapal, Karthick <kjeyapal@akamai.com>
Instead of silently ignoring the content_type option in listen mode,
apply its value to the provided "Content-Type:" header.
Signed-off-by: Moritz Barsnick <barsnick@gmx.net>
Reviewed-by: Nicolas George <george@nsup.org>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
We haven't had a stable release since the packet_gap addition, so probably it
is worth reworking the option to something that makes more sense to the end
user. Also add burst_bits option to specify maximum length of bit bursts.
Signed-off-by: Marton Balint <cus@passwd.hu>
This commit enables sending UDP packets in a background thread with specified delay.
When sending packets without a delay some devices with small RX buffer
( MAG200 STB, for example) will drop tail packets in bursts causing
decoding errors.
To use it specify "fifo_size" with "packet_gap" .
The output url will looks like udp://xxx:yyy?fifo_size=<output fifo
size>&packet_gap=<delay in usecs>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
* commit '933dec0e29ec4d2cb83474279a6c52d62fdb7310':
file: Add an option for following a file that is being written
Merged-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
Using this requires setting the rw_timeout option to make it
terminate, alternatively using the interrupt callback (if used via
the API).
Signed-off-by: Martin Storsjö <martin@martin.st>
If set non-zero, this limits duration of the retry_transfer_wrapper()
loop, thus affecting ffurl_read*(), ffurl_write(). As soon as
one single byte is successfully received/transmitted, the timer
restarts.
This has further changes by Michael Niedermayer and Martin Storsjö.
Signed-off-by: Martin Storsjö <martin@martin.st>
adds two new options that may be set via the dictionary:
- send_buffer_size
- recv_buffer_size
When present, setsockopt() is used with SO_SNDBUF and SO_RCVBUF to set
socket buffer sizes. I chose to make send and receive independent
because buffering requirements are often asymmetric.
Errors in setting the buffer size mean the socket will use its
default, so they are ignored.
There is no sanity checking on values, as the kernel/socket layers
already impose reasonable limits if asked for something crazy.
Rationale for enlarging receive buffers is to reduce susceptibility
to intermittent network delays/congestion. I added setting the send
buffer for symmetry.
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
