Since 596e5d4783, this is not necessary anymore. It also allows to
actually disable the flushing, improving write performance (but
possibly giving worse latency in real-time streaming).
Signed-off-by: Martin Storsjö <martin@martin.st>
This is enabled by default and can be disabled with
"-fflags -flush_packets".
Inspired by a patch from Nicolas George <nicolas.george@normalesup.org>.
Signed-off-by: Martin Storsjö <martin@martin.st>
If we really want to support parameter changes, they need to be
signalled along with the AVPackets as parameter change side data,
not just changing the AVCodecContext parameters when a packet
is demuxed (since there may be other earlier packets yet undecoded).
Something similar was already done for the sample rate in 0883109b2,
but some parameters were left changeable.
This avoids having to recheck the channel count for validity for
each decoded frame in (ad)pcm decoders, unless the decoders
explicitly say that they accept parameter changes.
Reported-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
Signed-off-by: Martin Storsjö <martin@martin.st>
Limit the size to INT_MAX/2 (for simplicity) to be sure that
size + BYTES_PER_FRAME_RECORD won't overflow.
Also factorize other existing error return paths.
Reported-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
Signed-off-by: Martin Storsjö <martin@martin.st>
Limit the size to INT_MAX/2 (for simplicity) to be sure that
size + FF_INPUT_BUFFER_PADDING_SIZE won't overflow.
Reported-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
Signed-off-by: Martin Storsjö <martin@martin.st>
The seektable is required for filling in ape->frames[i].pos
further down.
Reported-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
Signed-off-by: Martin Storsjö <martin@martin.st>
This makes sure the faststart vs fragmentation check works as
intended when fragmentation is enabled due to using the ismv mode.
Signed-off-by: Martin Storsjö <martin@martin.st>
This fixes warnings about making integers from pointers without
a cast, and avoids the theoretical case where the lower 32 bits of
the pointer would all be zero where the implicit cast wouldn't give
the right result.
Signed-off-by: Martin Storsjö <martin@martin.st>
This allows creation of frame accurate chapter marks from sources like
DVD and BD where the precise chapter location is not known until the
chapter mark has been reached during reading.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
This should improve write performance quite significantly.
---
Tested with both writing a normal mp4, by using the faststart
feature and writing a fragmented mp4 file; all turn out with the
same md5sum as before.
Signed-off-by: Martin Storsjö <martin@martin.st>
Remove the header decoding for PCM audio from mpeg.c and the
20/24bit parts from pcm.c and merge them into a new decoder in
pcm-dvd.c.
The decoder has added support for samples that span multiple
packets and modified 20/24bit group decoding. Both is needed to
decode samples that have been generated with DVD-Lab Pro 2. The
decoding of 16bit PCM and two channel 24bit is identical to
before. No other samples are known to verify the correctness of
the encoding this software does.
The complete list of tested formats is
48kHz/16bit/2-8 channels
48kHz/24bit/2-5 channels
96kHz/16bit/2-4 channels
96kHz/24bit/2 channels
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
When streaming to limelight, the app name is either a full
"appname/subaccount" or "appname/_definst_". In the latter case,
the app name can be simplified into simply "appname", but the
authentication hashing assumes the /_definst_ still to be present.
Signed-off-by: Martin Storsjö <martin@martin.st>
If a client tries to read the file while it's being updated, the client
would get an incomplete manifest. Instead write to a separate temp file
and atomically rename it to replace the previous one.
Signed-off-by: Martin Storsjö <martin@martin.st>
The element was only being written when the value == 1. But the default
value of this element is 1, so this has no useful effect. This element
needs to be written when the value == 0.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
On failures in the write_trailer function, we could also ignore
the errors and try to finish the file despite these errors (which
would only leave an incomplete chapters track). It's probably better
to signal the error clearly to the caller though (and if this
function failed there's no guarantee that there's enough memory to
finish the trailer either).
Signed-off-by: Martin Storsjö <martin@martin.st>
QuickTime will play multiple audio tracks concurrently if this flag is
set for multiple audio tracks. And if no subtitle track has this flag
set, QuickTime will show no subtitles in the subtitle menu.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
Faststart moves the moov atom to the beginning of the file and rewrites
the rest of the file after muxing is complete.
Signed-off-by: Martin Storsjö <martin@martin.st>
This allows creation of frame accurate chapter marks from sources
like DVD and BD where the precise chapter location is not known until
the chapter mark has been reached during reading.
Signed-off-by: Martin Storsjö <martin@martin.st>
Allow emitting the current cluster that is being written before
starting a new one, simplifying how to figure out where clusters
are positioned in the output stream (for live streaming).
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Seeking in certain broken files would cause ogg_read_timestamp
to fail because ogg_packet would go into a state where all packets
of stream 1 would be discarded until the end of the stream.
Bug-Id: 553
CC: libav-stable@libav.org
Signed-off-by: Jan Gerber <j@v2v.cc>
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
The mov/mp4 muxer has support for handling negative timestamps
via edit lists (which customarily is used for handling the 1-frame
delay due to B-frames as well).
Using the muxer's native way of handling it is better than using
the generic offsetting. The generic offsetting is a bit too
crude when e.g. the timebase of one track is 1/fps, where the
edit lists can handle it accurately.
Signed-off-by: Martin Storsjö <martin@martin.st>
The counter itself shouldn't be wrapped, since it is used for
determining end_pts for the next segment - only wrap the number
used for the segment file name.
Signed-off-by: Martin Storsjö <martin@martin.st>
The hls muxer itself doesn't have any direct (object file level)
dependencies on mpegtsenc.o, and including that object file
directly doesn't ensure that it is registered so that the muxer
actually is accessible.
Signed-off-by: Martin Storsjö <martin@martin.st>
IPPROTO_IPV6 is unrelated here (it's only used in udp.c for
multicast sockopts), check for support for the sockaddr_in6
struct itself.
Signed-off-by: Martin Storsjö <martin@martin.st>
An SDP description normally only contains the target IP address
and port for the packets. This means that we don't really have
any clue where to send the RTCP RR packets - previously they're
sent to the destination IP written in the SDP (at the same port),
which rarely is the actual peer. And if the source for the packets
is on a different port than the destination, it's never correct.
With a new option, we can choose to send the packets to the
address that the latest packet on each socket arrived from.
---
Some may even argue that this should be the default - perhaps,
but I'd rather keep it optional at first. Additionally, I'm not
sure if sending RTCP RR directly back to the source is
desireable for e.g. multicast.
Signed-off-by: Martin Storsjö <martin@martin.st>
If we've received packets on the same socket before, the return
packets are sent to that address. If we've only received packets
on the other socket, try to guess the source port for the other
one assuming the basic +1/-1 logic.
Signed-off-by: Martin Storsjö <martin@martin.st>
Move the sources documentation up below the marker for deprecated
otpions. Also mention the new block parameter, that was added
in 749722209.
Signed-off-by: Martin Storsjö <martin@martin.st>
It is possible to have an initial broken header and then valid packets.
Reported-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
Add one copy of the function into each of the libraries, similarly
to what we do for log2_tab. When using static libs, only one
copy of the file_open.o object file gets included, while when
using shared libraries, each of them get a copy of its own.
This fixes DLL builds with a statically linked C runtime, where
each DLL effectively has got its own instance of the C runtime,
where file descriptors can't be shared across runtimes.
On systems not using msvcrt, the function is not duplicated.
Signed-off-by: Martin Storsjö <martin@martin.st>
This supports non-Linux systems (SOCK_CLOEXEC is non-standard) and
older Linux kernels to the extent possible.
Signed-off-by: Martin Storsjö <martin@martin.st>
When libavformat was changed to use the new avpriv_open function
in 51eb213d00, this silently bypassed the existing wrapper for
win32. Move the win32 wrapper into libavutil/file.c to make sure
it gets called everywhere (not just in the libavformat case).
This makes sure that non-ascii file names gets opened properly
(where file names internally are stored as utf8, but they get
converted to wchar_t and opened with _wsopen).
Signed-off-by: Martin Storsjö <martin@martin.st>
This provides at least some protection against potential accidental
corruption of AVIO buffer workspace.
Signed-off-by: Martin Storsjö <martin@martin.st>
It's only relevant for the RTSP demuxer. Similarly, the custom_io
flag is only present in the SDP demuxer options list.
Signed-off-by: Martin Storsjö <martin@martin.st>
Also clear the AVIOContext handle after freeing, to avoid
possible dangling pointers if the later call fails.
Signed-off-by: Martin Storsjö <martin@martin.st>
