The x86 optimized dct_quantize only calculates the last nonzero
coefficient correctly if the zigzag scan order is used. For the
alternate scan order, this value is incorrect.
To work around this, the dct_unquantize functions process the entire
block if the alternate scan order is used.
But a second workaround (bb198e198a) was added that recalculates the
last nonzero coefficient after dct_quantize is called if the alternate
scan order is used.
This commit removes the first workaround, which became redundant.
Set them in ff_mpv_idct_init() so that they are already set
in ff_mpv_decode_init(). This is in preparation for avoiding
to set dct_unquantize in every ff_mpv_frame_start().
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Introduced in 1992, the Alpha was a 64-bit RISC processor designed
to replace the VAX CISC machines sold by Digital Equipment Corporation.
After Digital was acquired by Compaq in 1998 -- who themselves would be
later purchased by Hewlett-Packard, the architecture was phased out over
the following decade. It became effectively defunct in 2007, the last
publicly available processor being the Alpha 21364.
FFmpeg has not added any DSP code for this architecture since lowres2
was introduced in 2012, and it is more than unlikely someone still wishes
to maintain it.
Remove the DSP and support code.
Signed-off-by: Vittorio Giovara <vittorio.giovara@gmail.com>
It has been added in a579db0c4f
due to XvMC, but today it is only used to swap U and V
for VCR2, a MPEG-2 variant with U and V swapped.
This can be done in a simpler fashion, namely by simply
swapping the U and V pointers of the corresponding
MPVWorkPictures.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
This also rids us of the requirement to preserve the PutBitContext
in ff_update_duplicate_context().
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Only set the ScratchpadContext and let the users that need it
(i.e. encoders) set the MotionEstContext stuff themselves.
Also add an explicit pointer to ScratchpadContext to point
to the allocated buffer so that none of the other scratchpad
pointers is singled out as being used for the allocations.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
These pointers point to the same buffers, so one can just
use a union for them and avoid synchronising one of them.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Up until now, an initialized MpegEncContext had an array of
MPVPictures (way more than were ever needed) and the MPVPicture*
contained in the MPVWorkPictures as well as the input_picture
and reordered_input_picture arrays (for the encoder) pointed
into this array. Several of the pointers could point to the
same slot and because there was no reference counting involved,
one had to check for aliasing before unreferencing.
Furthermore, given that these pointers were not ownership pointers
the pointers were often simply reset without unreferencing
the slot (happened e.g. for the RV30 and RV40 decoders) or
there were moved without resetting the src pointer (happened
for the encoders where the entries in the input_picture
and reordered_input_picture arrays were not reset).
Instead actually releasing these pictures was performed by looping
over the whole array and checking which one of the entries needed
to be kept. Given that the array had way too many slots (36),
this meant that more than 30 MPVPictures have been unnecessarily
unreferenced in every ff_mpv_frame_start(); something similar
happened for the encoder.
This commit changes this by making the MPVPictures refcounted
via the RefStruct API. The MPVPictures itself are part of a pool
so that this does not entail constant allocations; instead,
the amount of allocations actually goes down, because the
earlier code used such a large array of MPVPictures (36 entries) and
allocated an AVFrame for every one of these on every
ff_mpv_common_init(). In fact, the pool is only freed when closing
the codec, so that reinitializations don't lead to new allocations
(this avoids having to sync the pool in update_thread_context).
Making MPVPictures refcounted also has another key benefit:
It makes it possible to directly share them across threads
(when using frame-threaded decoding), eliminating ugly code
with underlying av_frame_ref()'s; sharing these pictures
can't fail any more.
The pool is allocated in ff_mpv_decode_init() for decoders,
which therefore can fail now. This and the fact that the pool
is not unreferenced in ff_mpv_common_end() also necessitated
to mark several mpegvideo-decoders with the FF_CODEC_CAP_INIT_CLEANUP
flag.
*: This also means that there is no good reason any more for
ff_mpv_common_frame_size_change() to exist.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There are two types of MPVPictures: Three (cur_pic, last_pic, next_pic)
that are directly part of MpegEncContext and an array of MPVPictures
that are separately allocated and are mostly accessed via pointers
(cur|last|next)_pic_ptr; they are also used to store AVFrames in the
encoder (necessary due to B-frames). As the name implies, each of the
former is directly associated with one of the _ptr pointers:
They actually share the same underlying buffers, but the ones
that are part of the context can have their data pointers offset
and their linesize doubled for field pictures.
Up until now, each of these had their own references; in particular,
there was an underlying av_frame_ref() to sync cur_pic and cur_pic_ptr
etc. This is wasteful.
This commit changes this relationship: cur_pic, last_pic and next_pic
now become MPVWorkPictures; this structure does not have an AVFrame
at all any more, but only the cached values of data and linesize.
It also contains a pointer to the corresponding MPVPicture, establishing
a more natural relationsship between the two.
This already means that creating the context-pictures from the pointers
can no longer fail.
What has not been changed is the fact that the MPVPicture* pointers
are not ownership pointers and that the MPVPictures are part of an
array of MPVPictures that is owned by a single AVCodecContext.
Doing so will be done in a latter commit.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
This avoids an indirection and is in preparation for removing
the AVFrame from MpegEncContext.(cur|last|next)_pic altogether.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
current_picture->cur_pic, last_picture->last_pic, similarly
for new_picture and next_picture.
Also rename the corresponding *_ptr fields.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
It is the only user of said table and doing so is especially
important given that this buffer is zeroed every time.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
It involves less allocations and therefore has less
potential errors to be checked. One consequence thereof
is that updating the picture tables can no longer fail.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
This avoids constant allocations+frees and will also allow
to simply switch to the RefStruct API, thereby avoiding
the overhead of the AVBuffer API.
It also simplifies the code, because it removes the "needs_realloc"
field: It was added in 435c0b87d2,
before the introduction of the AVBuffer API: given that these buffers
may be used by different threads, they were not freed immediately
and instead were marked as being freed later by setting needs_realloc.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
VC-1 can switch from between being progressive and interlaced
on a per-frame basis. In the latter case, the number of macroblocks
is aligned to two (or equivalently, the height to 32); therefore
certain buffers are allocated for the bigger mb_height
(see 950fb8acb4 and
017e234c20).
This commit changes how this is done: Aligning these buffers is
restricted to VC-1 and it is done directly by aligning
mb_height (but not MpegEncContext.mb_height) instead of
adding something in an ad-hoc manner.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
coded_block is only used for I-frames, so it is unnecessary
to reset it in ff_clean_intra_table_entries() (which
cleans certain tables for a non-intra MB).
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
The mpegvideo-based codecs currently require the linesize to be
constant (except when the frame dimensions change); one reason
for this is that certain scratch buffers whose size depend on
linesize are only allocated once and are presumed to be correctly
sized if the pointers are != NULL.
This commit changes this by storing the actual linesize these
buffers belong to and reallocating the buffers if it does not
suffice. This is not enough to actually support changing linesizes,
but it is a start. And it is a prerequisite for the next patch.
Also don't emit an error message in case the source ctx's
edge_emu_buffer is unset in ff_mpeg_update_thread_context().
It need not be an error at all; e.g. it is a perfectly normal
state in case a hardware acceleration is used as the scratch
buffers are not allocated in this case (it is easy to run into
this issue with MPEG-4) or if the src context was not initialized
at all (e.g. because the first packet contained garbage).
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There are lots of files that don't need it: The number of object
files that actually need it went down from 2011 to 884 here.
Keep it for external users in order to not cause breakages.
Also improve the other headers a bit while just at it.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
It is unnecessary since the removal of non-thread-safe callbacks
in e0786a8eeb. Since then, the
AVCodecContext has only been used as logcontext.
Removing ff_thread_release_buffer() allowed to remove AVCodecContext*
parameters from several other functions (not only unref functions,
but also e.g. ff_h264_ref_picture() which calls ff_h264_unref_picture()
on error).
Reviewed-by: Anton Khirnov <anton@khirnov.net>
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
It is only used by encoders; this unfortunately necessitated
to add separate allocations to the SVQ1 encoder which uses
motion estimation without being a full member of mpegvideo.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
This basically reverts cc0380222a.
At the time of said commit, cleanup on init failure was very
buggy. For codecs with the INIT_CLEANUP cap, the close function
could be called on error even before the private data has been
allocated; and when using frame threading the same could also
happen even without said flag. Some mpegvideo decoders were
affected by the latter.
Yet both of these issues have been fixed long ago, the latter
in commit e9b6617579. Therefore
the workaround in ff_mpv_common_end() can be removed.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Only encoders need two sets of int16_t [12][64]
(one to save the current best state and one for the current
working state); decoders need only one. This saves 1.5KiB
per slice context for a decoder.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
For the intra_[hv]_scantables, only ScanTable.permutated
is used, so one only needs to keep that.
Reviewed-by: Michael Niedermayer <michael@niedermayer.cc>
Reviewed-by: Peter Ross <pross@xvid.org>
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
It is only used by gmc/gmc1 which is only used by the MPEG-4
decoder, so move it to Mpeg4DecContext and rename it
to Mpeg4VideoDSP. Also compile it iff the MPEG-4 decoder is compiled.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
This has the advantage of not having to check for whether
a given MpegEncContext is actually a decoder or an encoder
context at runtime.
To do so, mpv_reconstruct_mb_internal() is moved into a new
template file that is included by both mpegvideo_enc.c
and mpegvideo_dec.c; the decoder-only code (mainly lowres)
are also moved to mpegvideo_dec.c. The is_encoder checks are
changed to #if IS_ENCODER in order to avoid having to include
headers for decoder-only functions in mpegvideo_enc.c.
This approach also has the advantage that it is easy to adapt
mpv_reconstruct_mb_internal() to using different structures
for decoders and encoders (e.g. the check for whether
a macroblock should be processed for the encoder or not
uses MpegEncContext elements that make no sense for decoders
and should not be part of their context).
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Up until now, we inlined lowres_flag as well as is_mpeg12
independently (unless CONFIG_SMALL was true); this commit
changes this to instead inline mpv_reconstruct_mb_internal()
(at most) four times, namely once for encoders, once for decoders
using lowres and once for non-lowres mpeg-1/2 decoders and once
for non-lowres non-mpeg-1/2 decoders (mpeg-1/2 is not inlined
in case of CONFIG_SMALL). This is neutral performance-wise,
but proved beneficial size-wise: It saved 1776B of .text
for GCC 11 or 1344B for Clang 14 (both -O3 x64).
Notice that inlining is_mpeg12 for is_encoder would not really
be beneficial, as the encoder codepath does mostly not depend
on is_mpeg12 at all.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
There are two types of checks for whether the current codec
is MPEG-1/2 in mpv_reconstruct_mb_internal(): Those that are
required for correctness and those that are not; an example
of the latter is "is_mpeg12 || (s->codec_id != AV_CODEC_ID_WMV2)".
The reason for the existence of such checks is that
mpv_reconstruct_mb_internal() has the av_always_inline attribute
and is_mpeg12 is usually inlined, so that in case we are dealing
with MPEG-1/2 the above check can be completely optimized away.
But is_mpeg12 is not always inlined: it is not in case
CONFIG_SMALL is true in which case is_mpeg12 is always zero,
so that the checks required for correctness need to check
out_format explicitly. This is currently done via a macro
in mpv_reconstruct_mb_internal(), so that the fact that
it is CONFIG_SMALL that determines this is encoded at two places.
This commit changes this by making is_mpeg12 a three-state:
DEFINITELY_MPEG12, MAY_BE_MPEG12 and NOT_MPEG12. In the second
case, one has to resort to check out_format, in the other cases
is_mpeg12 can be taken at face-value. This will allow to make
inlining is_mpeg12 more flexible in a future commit.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Some parts of mpegvideo.c behave differently depending
upon whether AVCodecContext.draw_horiz_band is set or not.
This differing behaviour makes lots of FATE tests fail
and leads to garbage output, although setting this callback
is not supposed to change the output at all.
These checks have been added in commits
3994623df2 and
b68ab2609c. The commit messages
do not contain a real reason for adding the checks and it is
indeed a mystery to me. But removing these checks fixes
the FATE tests when one adds an (empty) draw_horiz_band
when using a codec that claims to support it.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Fixes the rv20-1239 FATE-test.
Reviewed-by: Michael Niedermayer <michael@niedermayer.cc>
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
This commit moves the encoder-only allocations of the tables
owned solely by the main encoder context to mpegvideo_enc.c.
This avoids checks in mpegvideo.c for whether we are dealing
with an encoder; it also improves modularity (if encoders are
disabled, this code will no longer be included in the binary).
And it also avoids having to reset these pointers at the beginning
of ff_mpv_common_init() (in case the dst context is uninitialized,
ff_mpeg_update_thread_context() simply copies the src context
into dst which therefore may contain pointers not owned by it,
but this does not happen for encoders at all).
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
It is the proper place to set it, directly besides mb_width and
mb_stride. The reason for doing it the way it is done now seems
to be that the code does not create more slice contexts than necessary
(i.e. not more than one per row), so that this number needs to be
known before setting the number of slices. But this can always be
arranged by just moving the code that sets the number of slices.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
Also constify the corresponding code in mpegvideo.c that handles
lowres.
(Unfortunately, not everything that is const could be constified:
ref_picture could be made const uint8_t* const* if C allowed the
safe automatic conversion from uint8_t**; and pix_op, qpix_op
could be made to point to const function pointers, but C's handling
of const in pointers to arrays is broken.)
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@outlook.com>
