Since 1.0.0, this function is deprecated. A new function,
CRYPTO_THREADID_set_callback is available, but if not set at all,
it uses the address of errno as thread id, which should be
sufficient for most systems.
On windows, it never was necessary to use this function even
before 1.0.0, it used the right win32 API function for this
by default.
Signed-off-by: Martin Storsjö <martin@martin.st>
Calling the init function will become mandatory at some later
point. By calling it, more heavy network init (such as SSL/TLS
library init) can be done once at startup, instead of implicitly
when used (which could lead to it being done a number of times).
Signed-off-by: Martin Storsjö <martin@martin.st>
All current usages of it are incompatible with localization.
For example strcasecmp("i", "I") != 0 is possible, but would
break many of the places where it is used.
Instead use our own implementations that always treat the data
as ASCII.
Signed-off-by: Martin Storsjö <martin@martin.st>
p cannot be calculated before av_dup_packet since that one
might change avpkt->data, causing invalid reads and a
non-working range check.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
We keep INIT_AVX (for backwards compatibility). 3arg AVX ops with
a memory arg can only have it in src2, whereas SSE emulation of
3arg prefers to have it in src1 (i.e. the mov). So, if the op is
symmetric and the wrong one is memory, swap them.
* qatar/master:
http: Remove the custom function for disabling chunked posts
rtsp: Disable chunked http post through AVOptions
movdec: Set frame_size for AMR
h264_weight: remove duplication functions.
swscale: align vertical filtersize by 2 on x86.
libavfilter: reindent.
matroskadec: empty blocks are in fact valid.
avfilter: don't abort() on zero-size allocations.
h264: improve calculation of codec delay.
movenc: Set a correct packet size for AMR-NB mode 15, "no data"
avformat: Add functions for doing global network initialization
avformat: Add the https protocol
avformat: Add the tls protocol, using OpenSSL or gnutls
avformat: Initialize gnutls in ff_tls_init()
w32threads: Wrap the mutex functions in inline functions returning int
configure: Allow linking to the gnutls library
avformat: Add ff_tls_init()/deinit() that initialize OpenSSL
configure: Allow linking to openssl
avcodec: Allow locking and unlocking an avformat specific mutex
avformat: Split out functions from network.h to a new file, network.c
Conflicts:
Changelog
configure
doc/APIchanges
libavcodec/internal.h
libavcodec/version.h
libavfilter/formats.c
libavformat/matroskadec.c
libavformat/mov.c
libavformat/version.h
Merged-by: Michael Niedermayer <michaelni@gmx.at>
avctx->width/height remain right/bottom cropped as previous behaviour.
Hardware decoders need to know the uncropped data to allocate surfaces
of correct height. Some hardware is picky and fails to decoder properly
if a surface larger than needed is used during decode, so just aligning
up is not enough.
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
When constructing a channel layout string from individual channel names,
+ is a more practical separator than |, because it is usually not a shell
special character.
Signed-off-by: Nicolas George <nicolas.george@normalesup.org>
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
There were multiple issues, for example might we have to re-run
the decompression when the size of the buffer increased,
we should always use a decompression buffer large enough for
the header (so we do not get stuck when the size is too small).
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Treating them like 0 is safest, current code would invoke
undefined pointer arithmetic behaviour in this case.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
I am not sure these new values are correct, not am I sure
the semantics are a good idea since we do not seem to make any
use of them but they caused a lot of confusion, but this
seems to make things closer to matching the documentation.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
