In 16x8 motion compensation, for lower 16x8 region, the input to mpeg_motion() for motion_y was "motion_y + 16", which causes wrong rounding. For 4:2:0, chroma scaling for y is dividing by two and rounding toward zero. When motion_y < 0 and motion_y + 16 > 0, the rounding direction of "motion_y" and "motion_y + 16" is different and rounding "motion_y + 16" would be incorrect.
We should input "motion_y" as is to round correctly. I add "is_16x8" flag to do that.
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
For B field pictures, the spec says,
> The prediction shall be made from the field of the same parity as the field being predicted.
I did it.
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
This is done mainly in preparation for the SIMD patches.
- for the 8-bit input, decrease the blend factor precision to 7-bit.
- for the 16-bit input, increase the blend factor precision to 15-bit.
- make sure the blend functions are not called with 0 or maximum blending
factors, because we don't want the signed factor integers to overflow.
Fate test changes are due to different rounding.
Signed-off-by: Marton Balint <cus@passwd.hu>
<jamrial> durandal_1707: 8088b5d69c broke the acrossfade test
<@durandal_1707> jamrial: there was test?
<jamrial> durandal_1707: fate-filter-acrossfade
<@durandal_1707> what broke?
<jamrial> what used to be one frame is now two
<@durandal_1707> ahh, just update test
Signed-off-by: James Almer <jamrial@gmail.com>
The framerate filter was quite convoluted with some filter_frame /
request_frame logic bugs. It seemed easier to rewrite the whole filter_frame /
request_frame part and also the frame interpolation ratio calculation part in
one step.
Notable changes:
- The filter now only stores 2 frames instead of 3
- filter_frame outputs all the frames it can to be able to handle consecutive
filter_frame calls which previously caused early drops of buffered frames.
- because of this, request_frame is largely simplified and it only outputs
frames on flush. Previously consecuitve request_frame calls could cause the
filter to think it is in flush mode filling its buffer with the same frames
causing a "ghost" effect on the output.
- PTS discontinuities are handled better
- frames with unknown PTS values are now dropped
Fixes ticket #4870.
Probably fixes ticket #5493.
Signed-off-by: Marton Balint <cus@passwd.hu>
The PERSIST_RPARAM_A_RExt_Sony_1 bitstream has an out-of-range value
and has therefore been superseded.
It is otherwise identical, and decodes the same.
Signed-off-by: James Almer <jamrial@gmail.com>
It was truncated to int later on anyway. Fate test changes are due to rounding
instead of truncation.
Fixes fate test failures on x86-32 (gcc 4.8 (Ubuntu 4.8.5-2ubuntu1~14.04.1))
after 090b740680.
Signed-off-by: Marton Balint <cus@passwd.hu>
- normalize score to [0..100] instead of [0..85]
- change the default score to 8.2 to roughly keep existing behaviour
- take into account bit depth
- do not truncate to integer
Signed-off-by: Marton Balint <cus@passwd.hu>
Every bitstream filter behaves as intended now, so there's no need to
wait for the first packet of every stream.
Signed-off-by: James Almer <jamrial@gmail.com>
Writes one set of field framing information for progressive streams and
two sets for interlaced streams. Fixes ticket #6383.
Unfortunately the OpenDML v1.02 document is not very specific on what
value to use for start_line when frame data is not coming from a
capturing device, so this is just using 0/1 depending on the field order
as a best-effort guess.
Signed-off-by: Tobias Rapp <t.rapp@noa-archive.com>
After c2a8f0fcbe this can happen on normal edit lists starting on a B-frame.
Signed-off-by: Sasi Inguva <isasi@google.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Previously alac encoder was used, from a first glance I thought it is bitexact,
but it turns out it is using floating point arithmetic as well, so probably it
is not. Fixes fate failures on mingw32/64.
Signed-off-by: Marton Balint <cus@passwd.hu>
* commit '07a2b155949eb267cdfc7805f42c7b3375f9c7c5':
Bump major versions of all libraries
A few API deprecated ~2 years ago or more are also postponed here for
varying reasons.
FF_API_LOWRES:
Since this functionality depends on AVStream->codec, i figure the two can
be removed at the same time in the next bump or so.
FF_API_AVCTX_TIMEBASE:
Couldn't get this one to work. Not just libavcodec but apparently also
libavformat and ffmpeg.c expect AVCodecContext->time_base to be set for
decoding. Upon removal some tests report a different generic stream time
base (like 1/25), and others lose packet duration values. I guess it's
somehow tied to the AVStream->codec clusterfuck.
It can be dealt with alongside FF_API_LAVF_AVCTX in the next bump.
FF_API_OLD_FILTER_OPTS_ERROR:
This one is meant to remain after FF_API_OLD_FILTER_OPTS is removed.
Its purpose is displaying the corrected command line using the new syntax
as a suggestion as part of the error message.
Merged-by: James Almer <jamrial@gmail.com>
Sets the correct start padding value when an edit list is present.
A new fate test is added, fate-mov-440hz-10ms, to ensure this is
handled correctly.
Signed-off-by: Dale Curtis <dalecurtis@chromium.org>
Reviewed-by: Sasi Inguva <isasi-at-google.com@ffmpeg.org>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
Use the appropriate metadata filter for each codec - in the absence of any
options to modify the stream, the output bitstream should be identical to
the input (though the output file may differ in padding).
All tests use conformance bitstreams, the MPEG-2 streams are newly added
from the conformance test streams
<http://standards.iso.org/ittf/PubliclyAvailableStandards/ISO_IEC_13818-4_2004_Conformance_Testing/Video/>
(cherry picked from commit 3cae7f8b9b)
(cherry picked from commit fbd63170bc)
