This sends NACK for missed packets and PLI (picture loss indication)
if a depacketizer indicates that it needs a new keyframe, according
to RFC 4585.
This is only enabled if the SDP indicated that feedback is supported
(via the AVPF or SAVPF profile names).
The feedback packets are throttled to a certain maximum interval
(currently 250 ms) to make sure the feedback packets don't eat up
too much bandwidth (which might be counterproductive). The RFC
specifies a more elaborate feedback packet scheduling.
The feedback packets are currently sent independently from normal
RTCP RR packets, which is not totally spec compliant, but works
fine in the environments I've tested it in. (RFC 5506 allows this,
but requires a SDP attribute for enabling it.)
Signed-off-by: Martin Storsjö <martin@martin.st>
To use this, set sdpflags=custom_io to the sdp demuxer. During
the avformat_open_input call, the SDP is read from the AVFormatContext
AVIOContext (ctx->pb) - after the avformat_open_input call,
during the av_read_frame() calls, the same ctx->pb is used for reading
packets (and sending back RTCP RR packets).
Normally, one would use this with a read-only AVIOContext for the
SDP during the avformat_open_input call, then close that one and
replace it with a read-write one for the packets after the
avformat_open_input call has returned.
This allows using the RTP depacketizers as "pure" demuxers, without
having them tied to the libavformat network IO.
Signed-off-by: Martin Storsjö <martin@martin.st>
Streams from RTSP or SDP that do not match an allowed type will
be skipped entirely, which allows video-only or audio-only
streaming from servers that provide both.
Signed-off-by: Martin Storsjö <martin@martin.st>
Eventually, the old way of passing options by adding
stuff to the URL can be dropped.
This avoids having to tamper with the user-specified URL to
pass options on the transport mode. This also works better
with redirects, since the options don't need to be parsed out
from the URL.
Signed-off-by: Martin Storsjö <martin@martin.st>
This eases adding options that are common for both. The
AV_OPT_FLAG_EN/DECODING_PARAM still indicates whether they belong
to the muxer or demuxer.
Signed-off-by: Martin Storsjö <martin@martin.st>
This is more like what VLC does. If the server doesn't mention
supporting GET_PARAMETER in response to an OPTIONS request,
VLC doesn't send any keepalive requests at all. After this patch,
libavformat will still send OPTIONS keepalives if GET_PARAMETER
isn't explicitly said to be supported.
Some RTSP cameras don't support GET_PARAMETER, and will
close the connection if this is sent as keepalive request
(but support OPTIONS just fine, but probably don't need any
keepalive at all). Some other cameras don't support using
OPTIONS as keepalive, but require GET_PARAMETER instead.
Signed-off-by: Martin Storsjö <martin@martin.st>
If filtered, only packets from the right source address and port
are received.
To test, play back e.g. some mpeg4 video RTSP stream (where the
video stream is the first stream in the presentation) over UDP.
While receiving this stream, send another stream to the same port:
ffmpeg -re -i <whatever> -vcodec mpeg4 -an -f rtp
rtp://127.0.0.1:5000?localport=1234
Normally, the RTSP playback reports lots of errors at this point.
If the RTSP stream has the ?filter_src option enabled, these
interferring packets are ignored.
Originally committed as revision 26246 to svn://svn.ffmpeg.org/ffmpeg/trunk
This avoids having a large temporary buffer in the struct used for
storing the rtsp reply headers.
Originally committed as revision 26192 to svn://svn.ffmpeg.org/ffmpeg/trunk
This allows ff_rtsp_parse_line to do more changes directly in RTSPState
when parsing the reply, instead of having to store large amounts of
temporary data in RTSPMessageHeader.
Originally committed as revision 26190 to svn://svn.ffmpeg.org/ffmpeg/trunk
message, if available (RFC 2326, section 12.39), fixes issue 2212.
Patch by John Wimer <john at god vtic net>.
Originally committed as revision 25032 to svn://svn.ffmpeg.org/ffmpeg/trunk
