The code was blindly assuming that Zbb or V implied Zba. While the
earlier is practically always true, the later broke some QEMU setups,
as V was introduced earlier than Zba.
This commit enabled assembly code with intel AVX512 VNNI and added unit test for sobel filter
sobel_c: 4537
sobel_avx512icl 2136
Signed-off-by: bwang30 <bin.wang@intel.com>
Signed-off-by: Haihao Xiang <haihao.xiang@intel.com>
Unfortunately, it is common, and will remain so, that the Bit
manipulations are not enabled at compilation time. This is an official
policy for Debian ports in general (though they do not support RISC-V
officially as of yet) to stick to the minimal target baseline, which
does not include the B extension or even its Zbb subset.
For inline helpers (CPOP, REV8), compiler builtins (CTZ, CLZ) or
even plain C code (MIN, MAX, MINU, MAXU), run-time detection seems
impractical. But at least it can work for the byte-swap DSP functions.
RVV defines a total of 12 different extensions, including:
- 5 different instruction subsets:
- Zve32x: 8-, 16- and 32-bit integers,
- Zve32f: Zve32x plus single precision floats,
- Zve64x: Zve32x plus 64-bit integers,
- Zve64f: Zve32f plus Zve64x,
- Zve64d: Zve64f plus double precision floats.
- 6 different vector lengths:
- Zvl32b (embedded only),
- Zvl64b (embedded only),
- Zvl128b,
- Zvl256b,
- Zvl512b,
- Zvl1024b,
- and the V extension proper: equivalent to Zve64f and Zvl128b.
In total, there are 6 different possible sets of supported instructions
(including the empty set), but for convenience we allocate one bit for
each type sets: up-to-32-bit ints (RVV_I32), floats (RVV_F32),
64-bit ints (RVV_I64) and doubles (RVV_F64).
Whence the vector size is needed, it can be retrieved by reading the
unprivileged read-only vlenb CSR. This should probably be a separate
helper macro if needed at a later point.
This introduces compile-time and run-time CPU detection on RISC-V. In
practice, I doubt that FFmpeg will ever see a RISC-V CPU without all of
I, F and D extensions, and if it does, it probably won't have run-time
detection. So the flags are essentially always set.
But as things stand, checkasm wants them that way. Compare the ARMV8
flag on AArch64. We are nowhere near running short on CPU flag bits.
Old one was written with the assumption only even inputs would be given.
This very messy replacement supports even and odd inputs, and supports
AVX2 for extra speed. The buffers given are usually quite big (4k samples),
so the speedup is worth it.
The new SSE version is still faster than the old inline asm version by 33%.
Also checkasm is provided to make sure this monstrosity works.
This fixes some FATE tests.
- ff_pix_abs16_neon
- ff_pix_abs16_xy2_neon
In direct micro benchmarks of these ff functions verses their C implementations,
these functions performed as follows on AWS Graviton 3.
ff_pix_abs16_neon:
pix_abs_0_0_c: 141.1
pix_abs_0_0_neon: 19.6
ff_pix_abs16_xy2_neon:
pix_abs_0_3_c: 269.1
pix_abs_0_3_neon: 39.3
Tested with:
./tests/checkasm/checkasm --test=motion --bench --disable-linux-perf
Signed-off-by: Jonathan Swinney <jswinney@amazon.com>
Signed-off-by: Martin Storsjö <martin@martin.st>
Note that the benchmarking results for these functions are highly dependent
upon the input data. Therefore, each function is benchmarked twice,
corresponding to the best and worst case complexity of the reference C
implementation. The performance of a real stream decode will fall somewhere
between these two extremes.
Signed-off-by: Ben Avison <bavison@riscosopen.org>
Signed-off-by: Martin Storsjö <martin@martin.st>
This avoids unnecessary rebuilds of most source files if only the
list of enabled components has changed, but not the other properties
of the build, set in config.h.
Signed-off-by: Martin Storsjö <martin@martin.st>
LSX and LASX is loongarch SIMD extention.
They are enabled by default if compiler support it, and can be disabled
with '--disable-lsx' '--disable-lasx'.
Change-Id: Ie2608ea61dbd9b7fffadbf0ec2348bad6c124476
Reviewed-by: Shiyou Yin <yinshiyou-hf@loongson.cn>
Reviewed-by: guxiwei <guxiwei-hf@loongson.cn>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
This sadly required making changes to the code itself,
due to the same context needing to be reused for both versions.
The lookup table had to be duplicated for both versions.
Add MMI & MSA runtime detection for MIPS.
Basically there are two code pathes. For systems that
natively support CPUCFG instruction or kernel emulated
that instruction, we'll sense this feature from HWCAP and
report the flags according to values grab from CPUCFG. For
systems that have no CPUCFG (or not export it in HWCAP),
we'll parse /proc/cpuinfo instead.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Shiyou Yin <yinshiyou-hf@loongson.cn>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
