AVFMT_NOTIMESTAMPS for crc, as it ignores the timestamps.
AVFMT_VARIABLE_FPS for framecrc, as it prints dts.
Many FATE changes, because avconv is no longer duplicating frames in
those tests.
Also added -vsync 0 for some tests to prevent avconv from dropping
frames until it can be fixed more properly.
AVFMT_NOTIMESTAMPS for md5, as it ignores the timestamps.
AVFMT_VARIABLE_FPS for framemd5, as it prints dts.
-vsync 0 for the vp8 test is needed because with vsync 2 the timestamp
guessing code gets confused by an altref frame that is never displayed
and drops a frame later.
Adding the thread count in frame level multithreading to has_b_frames
as an additional delay causes more problems than it solves.
For example inconsistent behaviour during timestamp calculation in
libavformat.
Thread count and frame level multithreading are both set by the user.
If the additional delay caused by frame level multithreading needs
to be considered in the calling code it has all information to take
it into account.
Should it become necessary to calculate a maximum delay inside
libavcodec it should be exported as its own field and not reusing
an existing field.
Based on a patch by Michael Niedermayer.
Signed-off-by: Janne Grunau <janne-libav@jannau.net>
Note: FCPublish/FCUnpublish are adobe server specific and not described
in the rtmp specification. Some servers might not cope with them at
all.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
The Apple HTTP Live Streaming demuxer's implementation of
seeking searches for the MPEG TS segment which contains the
requested timestamp. In its current implementation it assumes
that the first segment will start from 0.
But, MPEG TS streams do not necessarily start with timestamp
(near) 0, causing seeking to fail for those streams.
This also occurs when using live streaming of HTTP Live Streams.
In this case sliding playlists may be used, which means that in
that case only the last x encoded segments are stored, the earlier
segments get deleted from disk and removed from the playlist.
Because of this, when starting playback of a stream in the middle
of such a broadcast, the initial segment fetched after parsing
the m3u8 playlist will not start from timestamp (near) 0, causing
(the admittedly limited live) seeking to fail.
This patch changes this demuxers seeking implementation to use
the initial DTS as an offset for searching the segments containing
the requested timestamp.
Signed-off-by: Martin Storsjö <martin@martin.st>
The tls protocol handles connections via proxies internally.
With TLS/SSL, the peer verification requires that the client
speaks directly with the server, since the proxy doesn't have
the remote server's private key.
Signed-off-by: Martin Storsjö <martin@martin.st>
This opens a plain TCP connection through the proxy via the
CONNECT HTTP method. Normally, this is allowed for connections
on port 443, but can in general be used to allow connections
to any port (depending on proxy configuration), and could thus
be used to tunnel any TCP connection via a HTTP proxy.
Signed-off-by: Martin Storsjö <martin@martin.st>
RTCP timestamps are only necessary to synchronize time between
multiple streams. For a single stream, the RTP packet timestamp
provides more reliable timing. As a result, single-stream RTP
sessions should now have accurate and monotonic PTS.
Signed-off-by: Martin Storsjö <martin@martin.st>
TLSv1 is compatible with SSLv3, so this doesn't change much
in terms of compatibility. By explicitly using TLSv1, OpenSSL
sends the server name indication (SNI) header, which we
already set using SSL_set_tlsext_host_name (earlier, this
didn't have any effect).
SNI allows servers to serve SSL content for different host
names with separate certificates on one single port (vhosts).
Signed-off-by: Martin Storsjö <martin@martin.st>
This makes the function accept the format of creation_time
as output by demuxers (e.g. the mov demuxer), making the
creation timestamp stay intact if transcoding.
Signed-off-by: Martin Storsjö <martin@martin.st>
This function is used in muxers for parsing the 'creation_time'
metadata key, for converting it to a time value.
This makes it match the behaviour of the exported 'creation_time'
metadata from demuxers, where it is in UTC, too.
Signed-off-by: Martin Storsjö <martin@martin.st>
Converting to double before the multiplication rather than after
avoids an integer overflow in some cases.
Signed-off-by: Mans Rullgard <mans@mansr.com>
The interrupt callback has to be passed in during opening (setting it
after opening isn't enough), since a blocking open couldn't be
interrupted otherwise.
Options are passed down to procotols and also need to be available
during open() in most cases.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
This is a better io interrupt callback function, which has an
opaque parameter, which is given to the interrupt callback.
This allows callers to precisely cancel IO for one single
AVFormatContext, without interrupt other ones in the same
process.
Note, it's not needed in AVIOContext, at the moment.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
Add a decoder for the VBLE Lossless Codec, which
still has a cult following. Used to be popular
several years ago on doom9.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
Signed-off-by: Martin Storsjö <martin@martin.st>
This is needed because the twinvq decoder cannot rely on bit_rate to be set.
The API documentation says that bit_rate is set by libavcodec, not by the
user.
Tested with both Basic and Digest authentication, and tested with
both proxy authentication and authentication for the requested
resource at the same time.
Signed-off-by: Martin Storsjö <martin@martin.st>
The error was hidden before, to avoid showing an error on the
first request where no auth has been provided, when the server
indicates which authentication method to use.
Now the error is printed if an authentication method was used,
but failed.
Signed-off-by: Martin Storsjö <martin@martin.st>
The chunksize internal variable has two different uses - for
reading, it's the amount of data left of the current chunk
(or -1 if the server doesn't send data in chunked mode), where
it's only an internal state variable. For writing, it's used
to decide whether to enable chunked encoding (by default), by
using the value 0, or disable chunked encoding (value -1).
This, while consistent, doesn't make much sense to expose
as an AVOption. This splits the usage of the internal variable
into two variables, chunksize which is used for reading (as
before), and chunked_post which is the user-settable option,
with the values 0 and 1, where 1 is default.
Signed-off-by: Martin Storsjö <martin@martin.st>
