And make it const, so the caller doesn't attempt to change it.
ff_get_muxer_ts_offset() should be used to get the muxer timestamp offset.
Signed-off-by: James Almer <jamrial@gmail.com>
These made sense before 3ebf449766
when the creation of these boxes was specifically requested by the
user, but now they have become unnecessary as they are just like
many other boxes: If the input has the information required, they
are written, otherwise they are not.
They were moved to verbose verbosity level (which happens to be
the last level still relatively usable), and now appear either once
(normal MP4 muxing), or thrice (with the faststart flag set) in
any normal MP4 usage, without giving much useful information. Thus,
remove them in their current form.
If the edit lists remove parts of the output timeline, or add a
delay to it, this should be included in the mvhd/tkhd/mdhd durations,
which should correspond to the edit lists.
For tracks starting with pts < 0, the edit list trims out the segment
before pts=0. For tracks starting with pts > 0, a delay element is
added in the edit list, delaying the start of the track data.
In both cases, the practical effect is that the post-edit output
is as if the track had started with pts = 0. Thus calculate the range
from pts=0 to end_pts, for the purposes of mvhd/tkhd/mdhd, unless
edit lists explicitly are disabled.
mov_write_edts_tag needs to operate on the actual pts duration of
the track samples, not the duration that already takes the edit
list effect into account.
Signed-off-by: Martin Storsjö <martin@martin.st>
The 'alac' identifier has been registered to ISO and thus towards
ISOBMFF at the MP4 registration authority. The existing non-MOV
mux mode matches the official ALAC-in-MP4 specification.
The buffers used when fragmented output is enabled have up until now not
been freed in the deinit function; they leak e.g. if one errors out of
mov_write_trailer() before one reaches the point where they are normally
written out and freed. This can e.g. happen if allocating new vos_data
fails at the beginning of mov_write_trailer().
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
Otherwise the old data leaks whenever extradata needs to be rewritten
(e.g. when encoding FLAC with our encoder that sends an updated
extradata packet at the end).
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
When remuxing an rtp hint stream (or any stream with the tag "rtp "),
the mov muxer treats this as one of the rtp hint tracks it creates
internally when ordered to do so; yet this track lacks the
AVFormatContext for the hinting rtp muxer, leading to segfaults in
mov_write_udta_sdp() if a "trak" atom is written for this stream; if not,
the stream's codecpar is freed by mov_free() as if the mov muxer owned
it (it does for the internally created "rtp " tracks), but without
resetting st->codecpar, leading to double-frees lateron. This commit
therefore ignores said tag which makes rtp hint streams unremuxable.
This fixes tickets #8181 and #8186.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
There are two possible kinds of timecode tracks (with tag "tmcd") in the
mov muxer: Tracks created internally by the muxer and timecode tracks
sent by the user. If any of the latter exists, the former are
deactivated. The former all belong to another track, the source
track; the latter don't have a source track set, but the index of the
source track is initially zeroed by av_mallocz_array(). This is a
problem since 3d894db700: Said commit added
a function that calculates the duration of tracks and the duration of
timecode tracks is calculated by rescaling the duration (calculated by
the very same function) of the source track. This gives an infinite
recursion if the first track (the one that will be treated as source
track for all timecode tracks) is a timecode track itself, leading to a
stack overflow.
This commit fixes this by not using the nonexistent source track
when calculating the duration of timecode tracks not created internally
by the mov muxer.
Reviewed-by: Martin Storsjö <martin@martin.st>
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
If the average bit rate cannot be calculated, such as in the case
of streamed fragmented mp4, utilize various available parameters
in priority order.
Tests are updated where the esds or btrt or ISML manifest boxes'
output changes.
This is utilized by various media ingests to figure out the bit
rate of the content you are pushing towards it, so write it for
video, audio and subtitle tracks in case at least one nonzero value
is available. It is only mentioned for timed metadata sample
descriptions in QTFF, so limit it only to ISOBMFF (MODE_MP4) mode.
Updates the FATE tests which have their results changed due to the
20 extra bytes being written per track.
The write_colr flag has been marked as experimental for over 5 years.
It should be safe to enable its behavior by default as follows:
- Write the colr atom by default for mp4/mov if any of the following:
- The primaries/trc/matrix are all specified, OR
- There is an ICC profile, OR
- The user specified +write_colr
- Keep the write_colr flag for situations where the user wants to
write the colr atom even if the color info is unspecified (e.g.,
http://ffmpeg.org/pipermail/ffmpeg-devel/2020-March/259334.html)
This fixes https://trac.ffmpeg.org/ticket/7961
Signed-off-by: Michael Bradshaw <mjbshaw@google.com>
When doing streamed output, with e.g. +dash, if the mfra box ended
up being larger than the AVIOContext write buffer, the (unchecked)
seeking back to update the box size would silently fail and produce
an invalid mfra box.
This is similar to how other boxes are written in fragmented mode.
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
This is a requirement of the AV1-ISOBMFF spec. Section 2.1.
General Requirements & Brands states:
* It SHALL have the av01 brand among the compatible brands array of the FileTypeBox
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
Move the copying of the frame to vos_data further up in the function,
so that when writing the actual frame data for the first frame, it's
clear that the stream really is in annex b format, for the cases where
we create extradata from the first frame.
Alternatively - we could invert the checks for bitstream format. If
extradata is missing, we can't pretend that the bitstream is in
mp4 form, because we can't even know the NAL unit length prefix size
in that case.
Also avoid creating extradata for AVC intra. If the track tag is
an AVC intra tag, don't copy the frame into vos_data - this matches
other existing cases of how vos_data and TAG_IS_AVCI interact in
other places.
Signed-off-by: Martin Storsjö <martin@martin.st>
Sticking a full frame in the extradata works, as the code for writing
the avcC/hvcC extracts the relevant parameter set NAL units - provided
that they actually exist in the frame.
Some encoders don't provide split out extradata directly on init (or
at all). In particular, the MediaFoundation encoder wrapper doesn't
always (depending on the actual encoder device) - this is the case for
Qualcomm's HEVC encoder on SD835, and also on some QSV H264 encoders).
This only works for cases where the moov hasn't already been written
(e.g. when not writing fragmented mp4 with empty_moov, unless using
the delay_moov option).
Signed-off-by: Martin Storsjö <martin@martin.st>
This generates a potential memory leak, and mixes side data from the last
packet with other properties from the first.
Keep all the properties from the first packet only in the output packet
instead.
Signed-off-by: James Almer <jamrial@gmail.com>
The mdcv atom isn't in ISO/IEC 14496-12:2015 but it is expected to be
added soon. See:
http://ffmpeg.org/pipermail/ffmpeg-devel/2020-April/259529.html
The mdcv atom is already parsed in FFmpeg in mov.c.
Signed-off-by: Michael Bradshaw <mjbshaw@google.com>
The switch cases were missing:
- Primaries: bt470m, film, smpte428, and ebu3213.
- TRCs: gamma22, gamma28, linear, log, log_sqrt, iec61966_2_4, bt1361,
iec61966_2_1, bt2020_10bit, and bt2020_12bit.
- Space: rgb, fcc, ycgco, bt2020_cl, smpte2085, chroma-derived-nc,
chroma-derived-c, and ictcp.
They also annoyingly remapped the following (which are functionally
equivalent but can be treated differently by clients):
- smpte240m primaries to smpte170m.
- smpte170m TRC to bt709.
- bt470bg color space to smpte170m.
The enum values in FFmpeg are the same values as ITU-T H.273 and
ISO/IEC 23001-8 so we can just use them directly, which is both simpler
and preserves the user intent.
Signed-off-by: Michael Bradshaw <mjbshaw@google.com>
The clli atom isn't in ISO/IEC 14496-12:2015 so the flag is marked as
experimental and the clli atom is not written by default.
The clli atom is already parsed by FFmpeg in mov.c.
Signed-off-by: Michael Bradshaw <mjbshaw@google.com>
The specifications are de-facto frozen now as they've already been used in
production for years, the author has indicated reluctance on IRC to change
it further, and the only potential changes would, from what I understand,
be forward-compatible.
Increasing it by 2048 entries per realloc is exessive.
Reduces memory usage, especially on long, non fragmented output.
Reviewed-by: Anton Khirnov <anton@khirnov.net>
Signed-off-by: James Almer <jamrial@gmail.com>
If 'write_colr' movflag is set, then movflag 'prefer_icc' can
be used to first look for an AV_PKT_DATA_ICC_PROFILE entry to
encode.
If ICC profile doesn't exist, default behaviour enabled by
'write_colr' occurs.
Signed-off-by: vectronic <hello.vectronic@gmail.com>
Certain types of OBUs are stripped away before muxing into Matroska and
ISOBMFF; there are two functions to do this: One that outputs by
directly writing in an AVIOContext and one that returns a freshly
allocated buffer with the units not stripped away copied into it.
The latter option is bad for performance, especially when the input
does already not contain any of the units intended to be stripped away
(this covers typical remuxing scenarios). Therefore this commit changes
this by avoiding allocating and copying when possible; it is possible if
the OBUs to be retained are consecutively in the input buffer (without
an OBU to be discarded between them). In this case, the caller receives
the offset as well as the length of the part of the buffer that contains
the units to be kept. This also avoids copying when e.g. the only unit
to be discarded is a temporal delimiter at the front.
For a 22.7mb/s file with average framesize 113 kB this improved the time
for the calls to ff_av1_filter_obus_buf() when writing Matroska from
313319 decicycles to 2368 decicycles; for another file with 1.5mb/s
(average framesize 7.3 kB) it improved from 34539 decicycles to 1922
decicyles. For these files the only units that needed to be stripped
away were temporal unit delimiters at the front.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
Signed-off-by: James Almer <jamrial@gmail.com>
If this is not done, the avio_write() calls will cause segfaults
immediately afterwards on error.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
Signed-off-by: James Almer <jamrial@gmail.com>
As per the PIFF standard, the timescale of 10000000
is recommended but not mandatory, so don't override
the user-set value.
A warning is shown for non-recommended values.
When the faststart option for the mov/mp4 muxer is used, the current
position (i.e. the size of the already written data pre-shifting) was
evaluated twice: First in an initialization and then again later,
overwriting the first value without having ever touched it. So remove
the initialization.
Also, the clone of this code in the Sega FILM muxer behaves the same and
has been treated the same.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
If not available, set flags to 24 (bits 4 and 5), to signal the wallclock value
is read at the time of writing the atom.
Signed-off-by: James Almer <jamrial@gmail.com>
Keep all the existing data fields as they are (there's lots and
lots of nontrivial calculation and heuristics based on them in
their current form), but derive the duration as the difference
between the pts of the first packet to the maximum pts+duration
(not necessarily the last packet); use this duration in any box
where the actual presentation duration is supposed to be.
Fixes: 8420
Signed-off-by: Martin Storsjö <martin@martin.st>
Converting explicit avio_flush() calls helps us to buffer more data and avoid
flushing the IO context too often which causes reduced IO throughput for
non-streamed file output.
The user can control FLUSH_POINT flushing behaviour using the -flush_packets
option, the default typically means to flush unless a non-streamed file output
is used, so this change should have no adverse effect on streaming even if it
is assumed that after an avio_flush() the output buffer is clean so small
seekbacks within the output buffer will work even when the IO context is not
seekable.
Signed-off-by: Marton Balint <cus@passwd.hu>
To make it consistent with other muxers.
The user can still control the generic flushing behaviour after write_header
(same way as after packets) using the -flush_packets option, the default
typically means to flush unless a non-streamed file output is used.
Therefore this change should have no adverse effect on streaming, even if it is
assumed that the first packet has a clean buffer, so small seekbacks within the
output buffer work even when the IO context is not seekable.
Signed-off-by: Marton Balint <cus@passwd.hu>
