Currently it's exported as AVFrame.pkt_pts, which is also the only use
for that field. The reason it is done like this is that lavc used to
export various codec-specific "timing" information in AVFrame.pts, which
is not done anymore.
Since it is confusing to the callers to have a separate field which is
used only for decoder timestamps and nothing else, deprecate pkt_pts and
use just AVFrame.pts everywhere.
Until now, the decoding API was restricted to outputting 0 or 1 frames
per input packet. It also enforces a somewhat rigid dataflow in general.
This new API seeks to relax these restrictions by decoupling input and
output. Instead of doing a single call on each decode step, which may
consume the packet and may produce output, the new API requires the user
to send input first, and then ask for output.
For now, there are no codecs supporting this API. The API can work with
codecs using the old API, and most code added here is to make them
interoperate. The reverse is not possible, although for audio it might.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
This API is intended to allow passing around codec parameters without
using full AVCodecContext (which also contains codec options and
encoder/decoder state).
In the unlikely situation the user decides to set ticks_per_frame
and timebase to a value large enough to overflow.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Use the new fields directly instead of the ones from AVPicture.
This removes a layer of indirection which serves no pratical purpose
whatsoever, and will help in removing AVPicture structure completely
later.
Every subtitle encoder/decoder seamlessly points to the new arrays,
so it is possible to deprecate AVSubtitleRect.pict.
Signed-off-by: Vittorio Giovara <vittorio.giovara@gmail.com>
The generic code in utils.c sets the AVFrame.pkt_dts field from the
packet it was supposedly decoded. This does not have to be true for a
fully asynchronous decoder like mmaldec. It could be overwritten with an
incorrect value. Even if the decoder doesn't determine the DTS (but sets
it to AV_NOPTS_VALUE), it's impossible to determine a correct value in
utils.c.
Decoders can now be marked with FF_CODEC_CAP_SETS_PKT_DTS, in which case
utils.c won't overwrite the field. The decoders are expected to set this
field (even if they only set it to AV_NOPTS_VALUE).
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
The rationale is that coded_frame was only used to communicate key_frame,
pict_type and quality to the caller, as well as a few other random fields,
in a non predictable, let alone consistent way.
There was agreement that there was no use case for coded_frame, as it is
a full-sized AVFrame container used for just 2-3 int-sized properties,
which shouldn't even belong into the AVCodecContext in the first place.
The appropriate AVPacket flag can be used instead of key_frame, while
quality is exported with the new AVPacketSideData quality factor.
There is no replacement for the other fields as they were unreliable,
mishandled or just not used at all.
Signed-off-by: Vittorio Giovara <vittorio.giovara@gmail.com>
Allocating coded_frame is what most encoders do anyway, so it makes
sense to always allocate and free it in a single place. Moreover a lot
of encoders freed the frame with av_freep() instead of the correct API
av_frame_free().
This bring uniformity to encoder behaviour and prevents applications
from erroneusly accessing this field when not allocated. Additionally
this helps isolating encoders that export information with coded_frame,
and heavily simplifies its deprecation.
Signed-off-by: Vittorio Giovara <vittorio.giovara@gmail.com>
This field is designed for marking codec properties useful to lavc internals.
Two internal capabilities are added:
- FF_CODEC_CAP_INIT_THREADSAFE: codec can be opened without locks;
- FF_CODEC_CAP_INIT_CLEANUP: codec frees memory if initialization fails.
This carries the pixel format that would be used if it were not for
hardware acceleration. This is equal to AVCodecContext.pix_fmt if
hardware acceleration is not in use.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
The application will destroy the underlying hardware handles when
get_format() gets called again. Also this ensures the
deinitialization takes place if the get_format callback returns an
error.
Regression from 1c80c9d7ef.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
When decoding, this field holds the inverse of the framerate that can be
written in the headers for some codecs. Using a field called 'time_base'
for this is very misleading, as there are no timestamps associated with
it. Furthermore, this field is used for a very different purpose during
encoding.
Add a new field, called 'framerate', to replace the use of time_base for
decoding.
Currently, the amount of padding inserted at the beginning by some audio
encoders, is exported through AVCodecContext.delay. However
- the term 'delay' is heavily overloaded and can have multiple different
meanings even in the case of audio encoding.
- this field has entirely different meanings, depending on whether the
codec context is used for encoding or decoding (and has yet another
different meaning for video), preventing generic handling of the codec
context.
Therefore, add a new field -- AVCodecContext.initial_padding. It could
conceivably be used for decoding as well at a later point.
