Also include zero in the table, eliminating a special case in the
decoder.
Signed-off-by: Niels Möller <nisse@southpole.se>
Signed-off-by: Anton Khirnov <anton@khirnov.net>
The scaling factor is constant so it is faster to scale the
FIR coefficients in the tables during compilation.
Signed-off-by: Janne Grunau <janne-libav@jannau.net>
* commit 'aaa44d0299338e3bc90128816c21dbfab06cdb48':
dca: support mixing LFE in dca_downmix.
Conflicts:
libavcodec/dcadec.c
Merged-by: Michael Niedermayer <michaelni@gmx.at>
Previous coefficients were producing a non-normalized, incorrect Lt/Rt downmix.
The new coefficients produce a standard Lo/Ro downmix with 3dB attenuation.
This should match the typical default coefficients used by DTS encoders.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
It was based on an old, seemingly incorrect specification, so default
coefficients were always used anyway.
Signed-off-by: Anton Khirnov <anton@khirnov.net>
* qatar/master:
dca: Switch dca_sample_rates to avpriv_ prefix; it is used across libs
ARM: use =const syntax instead of explicit literal pools
ARM: use standard syntax for all LDRD/STRD instructions
fft: port FFT/IMDCT 3dnow functions to yasm, and disable on x86-64.
dct-test: allow to compile without HAVE_INLINE_ASM.
x86/dsputilenc: bury inline asm under HAVE_INLINE_ASM.
dca: Move tables used outside of dcadec.c to a separate file.
dca: Rename dca.c ---> dcadec.c
x86: h264dsp: Remove unused variable ff_pb_3_1
apetag: change a forgotten return to return 0
Conflicts:
libavcodec/Makefile
libavcodec/dca.c
libavcodec/x86/fft_3dn.c
libavcodec/x86/fft_3dn2.c
libavcodec/x86/fft_mmx.asm
Merged-by: Michael Niedermayer <michaelni@gmx.at>
* qatar/master: (29 commits)
sbrdsp.asm: convert all instructions to float/SSE ones.
dv: cosmetics.
dv: check buffer size before reading profile.
Revert "AAC SBR: group some writes."
udp: Print an error message if bind fails
cook: extend channel uncoupling tables so the full bit range is covered.
roqvideo: cosmetics.
roqvideo: convert to bytestream2 API.
dca: don't use av_clip_uintp2().
wmall: fix build with -DDEBUG enabled.
smc: port to bytestream2 API.
AAC SBR: group some writes.
dsputil: remove shift parameter from scalarproduct_int16
SBR DSP: unroll sum_square
rv34: remove dead code in intra availability check
rv34: clean a bit availability checks.
v4l2: update documentation
tgq: convert to bytestream2 API.
parser: remove forward declaration of MpegEncContext
dca: prevent accessing static arrays with invalid indexes.
...
Conflicts:
doc/indevs.texi
libavcodec/Makefile
libavcodec/dca.c
libavcodec/dvdata.c
libavcodec/eatgq.c
libavcodec/mmvideo.c
libavcodec/roqvideodec.c
libavcodec/smc.c
libswscale/output.c
Merged-by: Michael Niedermayer <michaelni@gmx.at>
* qatar/master: (34 commits)
dpcm: return error if packet is too small
dpcm: use smaller data types for static tables
dpcm: use sol_table_16 directly instead of through the DPCMContext.
dpcm: replace short with int16_t
dpcm: check to make sure channels is 1 or 2.
dpcm: misc pretty-printing
dpcm: remove unnecessary variable by using bytestream functions.
dpcm: move codec-specific variable declarations to their corresponding decoding blocks.
dpcm: consistently use the variable name 'n' for the next input byte.
dpcm: output AV_SAMPLE_FMT_U8 for Sol DPCM subcodecs 1 and 2.
dpcm: calculate and check actual output data size prior to decoding.
dpcm: factor out the stereo flag calculation
dpcm: cosmetics: rename channel_number to ch
avserver: Fix a bug where the socket is IPv4, but IPv6 is autoselected for the loopback address.
lavf: Avoid using av_malloc(0) in av_dump_format
dxva2_h264: pass the correct 8x8 scaling lists
dca: NEON optimised high freq VQ decoding
avcodec: reject audio packets with NULL data and non-zero size
dxva: Add ability to enable workaround for older ATI cards
latmenc: Set latmBufferFullness to largest value to indicate it is not used
...
Conflicts:
libavcodec/dxva2_h264.c
Merged-by: Michael Niedermayer <michaelni@gmx.at>
Passing an explicit filename to this command is only necessary if the
documentation in the @file block refers to a file different from the
one the block resides in.
Originally committed as revision 22921 to svn://svn.ffmpeg.org/ffmpeg/trunk
This reorders the lfe_fir tables, and drops the mirrored half,
such that the loops in lfe_interpolation_fir() can be simplified.
The new loop structure should be easier to implement with SIMD.
Static data size is reduced by 2kB.
3% faster on Cortex-A8.
Originally committed as revision 22849 to svn://svn.ffmpeg.org/ffmpeg/trunk
Optimised implementations of the synth filter will require these
arrays 16-byte aligned.
Originally committed as revision 22826 to svn://svn.ffmpeg.org/ffmpeg/trunk
Otherwise doxygen complains about ambiguous filenames when files exist
under the same name in different subdirectories.
Originally committed as revision 16912 to svn://svn.ffmpeg.org/ffmpeg/trunk
Consistently apply this rule: the guard name is obtained from the
filename by stripping the leading "lib", converting '/' and '.' to
'_' and uppercasing the resulting name. Guard names in the root
directory have to be prefixed by "FFMPEG_".
Originally committed as revision 15120 to svn://svn.ffmpeg.org/ffmpeg/trunk
Patch by Alexander Patrakov ($lastname <whirlpool> gmail.com)
Thread: dcadata.h: fir_32bands_perfect[] is wrong
Originally committed as revision 14964 to svn://svn.ffmpeg.org/ffmpeg/trunk
