1
0
mirror of https://github.com/FFmpeg/FFmpeg.git synced 2024-12-07 11:13:41 +02:00
FFmpeg/doc/swscale.txt
2012-10-31 00:37:42 +01:00

99 lines
4.6 KiB
Plaintext

The official guide to swscale for confused developers.
========================================================
Current (simplified) Architecture:
---------------------------------
Input
v
_______OR_________
/ \
/ \
special converter [Input to YUV converter]
| |
| (8bit YUV 4:4:4 / 4:2:2 / 4:2:0 / 4:0:0 )
| |
| v
| Horizontal scaler
| |
| (15bit YUV 4:4:4 / 4:2:2 / 4:2:0 / 4:1:1 / 4:0:0 )
| |
| v
| Vertical scaler and output converter
| |
v v
output
Swscale has 2 scaler paths. Each side must be capable of handling
slices, that is, consecutive non-overlapping rectangles of dimension
(0,slice_top) - (picture_width, slice_bottom).
special converter
These generally are unscaled converters of common
formats, like YUV 4:2:0/4:2:2 -> RGB12/15/16/24/32. Though it could also
in principle contain scalers optimized for specific common cases.
Main path
The main path is used when no special converter can be used. The code
is designed as a destination line pull architecture. That is, for each
output line the vertical scaler pulls lines from a ring buffer. When
the ring buffer does not contain the wanted line, then it is pulled from
the input slice through the input converter and horizontal scaler.
The result is also stored in the ring buffer to serve future vertical
scaler requests.
When no more output can be generated because lines from a future slice
would be needed, then all remaining lines in the current slice are
converted, horizontally scaled and put in the ring buffer.
[This is done for luma and chroma, each with possibly different numbers
of lines per picture.]
Input to YUV Converter
When the input to the main path is not planar 8 bits per component YUV or
8-bit gray, it is converted to planar 8-bit YUV. Two sets of converters
exist for this currently: One performs horizontal downscaling by 2
before the conversion, the other leaves the full chroma resolution,
but is slightly slower. The scaler will try to preserve full chroma
when the output uses it. It is possible to force full chroma with
SWS_FULL_CHR_H_INP even for cases where the scaler thinks it is useless.
Horizontal scaler
There are several horizontal scalers. A special case worth mentioning is
the fast bilinear scaler that is made of runtime-generated MMXEXT code
using specially tuned pshufw instructions.
The remaining scalers are specially-tuned for various filter lengths.
They scale 8-bit unsigned planar data to 16-bit signed planar data.
Future >8 bits per component inputs will need to add a new horizontal
scaler that preserves the input precision.
Vertical scaler and output converter
There is a large number of combined vertical scalers + output converters.
Some are:
* unscaled output converters
* unscaled output converters that average 2 chroma lines
* bilinear converters (C, MMX and accurate MMX)
* arbitrary filter length converters (C, MMX and accurate MMX)
And
* Plain C 8-bit 4:2:2 YUV -> RGB converters using LUTs
* Plain C 17-bit 4:4:4 YUV -> RGB converters using multiplies
* MMX 11-bit 4:2:2 YUV -> RGB converters
* Plain C 16-bit Y -> 16-bit gray
...
RGB with less than 8 bits per component uses dither to improve the
subjective quality and low-frequency accuracy.
Filter coefficients:
--------------------
There are several different scalers (bilinear, bicubic, lanczos, area,
sinc, ...). Their coefficients are calculated in initFilter().
Horizontal filter coefficients have a 1.0 point at 1 << 14, vertical ones at
1 << 12. The 1.0 points have been chosen to maximize precision while leaving
a little headroom for convolutional filters like sharpening filters and
minimizing SIMD instructions needed to apply them.
It would be trivial to use a different 1.0 point if some specific scaler
would benefit from it.
Also, as already hinted at, initFilter() accepts an optional convolutional
filter as input that can be used for contrast, saturation, blur, sharpening
shift, chroma vs. luma shift, ...