refreshWorktrees re-renders the branches view, because the branches view shows
worktrees against branches. This means that when both BRANCHES and WORKTREES are
requested to be refreshed, the branches view would be rendered twice in short
succession. This causes an ugly visual glitch when force-pushing a branch,
because when pushing is done, we would see the ↑4↓9 status come back from under
the Pushing status for a brief moment, to be replaced with a green checkmark a
moment later.
Fix this by including the worktree refresh in the branches refresh when both are
requested. This means that the two are no longer running in parallel for an
async refresh, but hopefully that's not so bad.
When pulling/pushing/fast-forwarding a branch, show this state in the branches
list for that branch for as long as the operation takes, to make it easier to
see when it's done (without having to stare at the status bar in the lower
left).
This will hopefully help with making these operations feel more predictable, now
that we no longer show a loader panel for them.
Very similar to WithWaitingStatus, except that the status is shown in a view
next to the affected item, rather than in the status bar.
Not used by anything yet; again, committing separately to get smaller commits.
This is not a complete fix, but it's good enough to fix the spurious test
failures of submodule/reset.go. We have some vague hope to fix this in a more
sustainable way by somehow improving our concurrency model fundamentally, but
that's a more long-term undertaking, and it's annoying that this test fails so
often, so let's fix it in this way for now.
A new gui config flag 'portraitMode':<string> is added to influence when
LazyGit stacks its UI components on top of one another.
The accepted values are 'auto', 'always', 'never'.
'auto': enter portrait mode when terminal becomes narrow enough
'always': always use portrait mode unconditional of the terminal
dimensions
'never': never use portraid mode
Signed-off-by: Louis DeLosSantos <louis.delos@gmail.com>
This is pretty funny: the staticcheck linter gets mad if we use a field which is marked
in a comment as being deprecated. But it tripped on my own comment saying that a field
is deprecated in terms of the user config!
Obviously we have to make use of this field, otherwise we would just remove it entirely
rather than mark it as deprecated, so I'm silencing this lint.
I doubt this lint would actually come in handy in other cases (like when using a third
party package) and worst case scenario we just end up fixing the problem when we
try to upgrade the package and the deprecated field is now gone).
We're going to make this user config struct a more authoritative source of truth.
Some of these fields weren't actually explained anywhere so I've added explanations.
In places where a lot of explanation is required I've linked to existing explanations in other docs.
This has several benefits:
- it's less code
- we're using the same mechanism to generate all our auto-generated files, so if
someone wants to add a new one, it's clear which pattern to follow
- we can re-generate all generated files with a single command
("go generate ./...", or "make generate")
- we only need a single check on CI to check that all files are up to date (see
previous commit)
At the moment, test_list.go is the only file that we generate using go:generate.
We will add another one in the next commit though, and we might add even more in
the future; it's useful to have a single check on CI that checks them all.
For the "cli" and "tui" modes of the test runner there's a "-race" parameter to
turn it on; for running tests on CI with go test, you turn it on by setting the
environment variable LAZYGIT_RACE_DETECTOR to a non-empty value.
This is useful for example to pass both -slow and -debug. Since we're about to
add yet another flag in the next commit, it becomes even more important. Plus,
it makes the code a little nicer too.
Previously there was no way to render a view's search status without also moving the cursor
to the current search match. This caused issues where we wanted to display the status
after leaving the view and coming back, or when beginning a new search from within the
view.
This commit separates the two use cases so we only move the cursor when we're actually
selecting the next search match
