This allows creation of frame accurate chapter marks from sources
like DVD and BD where the precise chapter location is not known until
the chapter mark has been reached during reading.
Signed-off-by: Martin Storsjö <martin@martin.st>
Allow emitting the current cluster that is being written before
starting a new one, simplifying how to figure out where clusters
are positioned in the output stream (for live streaming).
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Seeking in certain broken files would cause ogg_read_timestamp
to fail because ogg_packet would go into a state where all packets
of stream 1 would be discarded until the end of the stream.
Bug-Id: 553
CC: libav-stable@libav.org
Signed-off-by: Jan Gerber <j@v2v.cc>
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
The mov/mp4 muxer has support for handling negative timestamps
via edit lists (which customarily is used for handling the 1-frame
delay due to B-frames as well).
Using the muxer's native way of handling it is better than using
the generic offsetting. The generic offsetting is a bit too
crude when e.g. the timebase of one track is 1/fps, where the
edit lists can handle it accurately.
Signed-off-by: Martin Storsjö <martin@martin.st>
Implicit vector loads on POWER7 hardware can use the VSX
instruction set instead of classic Altivec/VMX. Let's force
a VMX load in this case.
Signed-off-by: Martin Storsjö <martin@martin.st>
The counter itself shouldn't be wrapped, since it is used for
determining end_pts for the next segment - only wrap the number
used for the segment file name.
Signed-off-by: Martin Storsjö <martin@martin.st>
The hls muxer itself doesn't have any direct (object file level)
dependencies on mpegtsenc.o, and including that object file
directly doesn't ensure that it is registered so that the muxer
actually is accessible.
Signed-off-by: Martin Storsjö <martin@martin.st>
IPPROTO_IPV6 is unrelated here (it's only used in udp.c for
multicast sockopts), check for support for the sockaddr_in6
struct itself.
Signed-off-by: Martin Storsjö <martin@martin.st>
An SDP description normally only contains the target IP address
and port for the packets. This means that we don't really have
any clue where to send the RTCP RR packets - previously they're
sent to the destination IP written in the SDP (at the same port),
which rarely is the actual peer. And if the source for the packets
is on a different port than the destination, it's never correct.
With a new option, we can choose to send the packets to the
address that the latest packet on each socket arrived from.
---
Some may even argue that this should be the default - perhaps,
but I'd rather keep it optional at first. Additionally, I'm not
sure if sending RTCP RR directly back to the source is
desireable for e.g. multicast.
Signed-off-by: Martin Storsjö <martin@martin.st>
If we've received packets on the same socket before, the return
packets are sent to that address. If we've only received packets
on the other socket, try to guess the source port for the other
one assuming the basic +1/-1 logic.
Signed-off-by: Martin Storsjö <martin@martin.st>
Move the sources documentation up below the marker for deprecated
otpions. Also mention the new block parameter, that was added
in 749722209.
Signed-off-by: Martin Storsjö <martin@martin.st>
It is possible to have an initial broken header and then valid packets.
Reported-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
The decompressed buffer can be used after codec_reinit, so it must be
preserved.
Reported-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
