It would never be called when the searched-for position
was already in the index.
In the other cases, the ogg_reset at the end of the
read_timestamp function handled it.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
In this case, the pts values will be delayed by one, but
at the same time pts values might only be supplied for e.g.
keyframes.
This results on only the frame after the keyframe having a
pts value.
As a hack, make read_timestamp return the keyframe position
together with the pts from a following frame when seeking
to a keyframe.
Fixes trac issue #438.
However it causes the read_timestamp function to return a
pos value that is actually before the packet with the
indicated pts.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
about twice as fast as before.
the not CONFIG_SMALL case is also droped as it is not faster than the
CONFIG_SMALL case.
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
We can handle v4 just fine, the parts we currently use
are the same for v3 and v4.
v4 can in addition contain an index which we so far do
not use though.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Fixes trac issue #438.
Seeking in that sample would cause ogg_read_timestamp to fail
because ogg_packet would go into a state where all packets
of stream 1 would be discarded until the end of the stream.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Line sizes are only 8-byte aligned, so use unaliged loads
for add_bytes_l2 pointers.
Increasing the alignment requirement to 16 seemed a bit extreme
(png may be used for rather small sizes).
Also fix a mov that had its arguments swapped, leading
add_bytes_l2 being applied on up to 8 bytes too few.
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Right now those muxers use the default timebase in all cases(1/90000).
This patch avoid unnecessary rescaling and makes the printed timestamps
more readable.
Also, extend the printed information to include the timebases and packet
pts/duration and align the columns.
Obviously changes the results of all fate tests which use those two
muxers.
* qatar/master:
libx264: fix indentation.
vorbis: fix overflows in floor1[] vector and inverse db table index.
win64: add a XMM clobber test configure option.
movdec: Parse the dvc1 atom
ARM: ac3: fix ac3_bit_alloc_calc_bap_armv6
swscale: K&R formatting cosmetics for Blackfin code
frwu: lowercase the FRWU codec name
movdec: fix dts generation in fragmented files
fate: make acodec-ac3_fixed test output raw AC3
APIchanges: add missing commit hashes
swscale: implement MMX, SSE2 and AVX functions for RGB32 input.
ra144enc: drop pointless "encoder" from .long_name
bethsoftvideo: fix palette reading.
mpc7: use av_fast_padded_malloc()
mpc7: simplify handling of packet sizes that are not a multiple of 4 bytes
doc: decoding Forward Uncompressed is supported
Fix a typo in the x86 asm version of ff_vector_clip_int32()
pcmenc: Do not set avpkt->size.
ff_alloc_packet: modify the size of the packet to match the requested size
Conflicts:
doc/APIchanges
libavcodec/libx264.c
libavcodec/mpc7.c
libavformat/isom.h
libswscale/Makefile
libswscale/bfin/yuv2rgb_bfin.c
tests/ref/fate/bethsoft-vid
tests/ref/seek/ac3_ac3
Merged-by: Michael Niedermayer <michaelni@gmx.at>
This will be useful to test more aggressively for failures to mark XMM
registers as clobbered in Win64 builds, and prevent regressions thereof.
Based on a patch by Ramiro Polla <ramiro.polla@gmail.com>
Normally, the actual payload data contains sequence headers, too,
and the parser can extract this and set it as extradata. However,
the data in the dvc1 atom is the "official" extradata for the file.
This is required for proper stream copy of vc1 from ismv to ismv.
Signed-off-by: Martin Storsjö <martin@martin.st>
Do not use AVStream's duration for dts generation since it contains in
some cases the duration of the whole file instead of duration of the
samples in the moov. This happens if the mdhd holds the duration of the
whole file but has no entries or a zero duration in its stts.
