Without the information, an application may choose audio from one
variant and video from another variant, which leads to fetching two
variants from the network. This enables av_find_best_stream() to find
matching audio and video streams, so that only one variant is fetched.
Signed-off-by: Martin Storsjö <martin@martin.st>
Also adjust the streams timestamps according to their start
timestamp when comparing. This helps getting correctly interleaved
packets if one stream lacks timestamps (such as a plain ADTS
stream when the other variants are full mpegts) when the others
have timestamps that don't start from zero.
This probably doesn't work properly if such a stream is
temporarily disabled (via the discard flags) and then reenabled,
and such streams are hard to correctly sync against the other
streams as well - but this works better than before at least.
The segment number restriction makes sure all variants advance
roughly at the same pace as well.
Signed-off-by: Martin Storsjö <martin@martin.st>
If passing the end of one segment while initializing the
chained demuxer, the parent demuxer's streams aren't set up
yet, so we can't recheck the discard flags.
Signed-off-by: Martin Storsjö <martin@martin.st>
This serves as a safeguard; normally we want to use the dts
comparison to interleave packets from all active variants. If that
dts comparison for some reason doesn't work as intended, make sure
that all packets in all variants for a certain sequence number have
been returned before moving on to the next one.
Signed-off-by: Martin Storsjö <martin@martin.st>
Incomplete crypted files would lead to a read after buffer boundary
otherwise.
Reported-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
Derived from VLC's http module.
Original authors:
Antoine Cellerier <dionoea@videolan.org>
Sébastien Escudier <sebastien-devel@celeos.eu>
Rémi Duraffort <ivoire@videolan.org>
Rémi Denis-Courmont <remi@remlab.net>
Francois Cartegnie <fcvlcdev@free.fr>
Normally, http servers shouldn't send this to us since we
don't advertise it with an Accept-Encoding header, but some
servers still do it anyway.
Signed-off-by: Martin Storsjö <martin@martin.st>
Only check dependencies if invoking the make targets 'check'
or anything matching 'fate%' except 'fate-rsync'.
Signed-off-by: Martin Storsjö <martin@martin.st>
This makes sure that values that are left-shifted by this constant
end up casted to 64 bit before shifting, avoiding overflow if the
value ends up larger than 2 GB.
Signed-off-by: Martin Storsjö <martin@martin.st>
Previously it was partly only added to central functions called
internally, however if GCC would inline these into the public fuction, the
alignment attribute would not take effect.
Instead, add it to all public entry points to avoid these problems.
Signed-off-by: Martin Storsjö <martin@martin.st>
Slice threading does not work with hardware acceleration, as decoding
is per-picture. This fixes Bugzilla #542.
Signed-off-by: Diego Biurrun <diego@biurrun.de>
VDPAU expects the bitstream value (0, 2 or 3).
libavcodec uses an enum (0, 1 or 2).
Signed-off-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: Diego Biurrun <diego@biurrun.de>
When building for iOS in thumb mode, gas-preprocessor.pl doesn't
mark unused labels as thumb functions (as it does for other
local labels, where it can figure out that they are functions
due to being referenced in branch instructions). This leads to
linker warnings for some of those local labels, such as:
ld: warning: ARM function not 4-byte aligned: __a_evaluation from
libavcodec/libavcodec.a(simple_idct_arm.o)
Therefore, comment them out since they don't have any function.
They do still have a value in documenting key points in the
assembly source though.
Signed-off-by: Martin Storsjö <martin@martin.st>
Before After
Mean StdDev Mean StdDev Change
This function 1323.0 98.0 746.2 60.6 +77.3%
Overall 15400.0 336.4 14147.5 288.4 +8.9%
Signed-off-by: Martin Storsjö <martin@martin.st>
Before After
Mean StdDev Mean StdDev Change
This function 1389.3 4.2 967.8 35.1 +43.6%
Overall 15577.5 83.2 15400.0 336.4 +1.2%
Signed-off-by: Martin Storsjö <martin@martin.st>
Before After
Mean StdDev Mean StdDev Change
This function 868.2 33.5 436.0 27.0 +99.1%
Overall 15973.0 223.2 15577.5 83.2 +2.5%
Signed-off-by: Martin Storsjö <martin@martin.st>
