Only flavors 0..3 seem to exist. E.g. rmdec.c treats any flavor > 3
as invalid data. Furthermore, we do not know how big the packets to
create ought to be given that for sipr these values are not read from
the bitstream, but from a table.
Furthermore, flavor is only used for sipr, so only check it for sipr;
rmdec.c does the same. (The old check for flavor being < 0 was
always wrong given that flavor is an int that is read via avio_rb16(),
so it has been removed completely.)
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
This makes decoding far more robust, since OggS, the ogg magic,
can be commonly found randomly in streams, which previously made
the demuxer think there's a new stream or a change in such.
v4l2_m2m uses device memory mapped buffers to store dequeued
frames/packets (reference counted by AVBufferRef). When the reference
count drops to zero, the buffer ownership is returned back to the
device, so that they can re-filled with frames/packets.
There are some cases when all the capture buffers are in userspace
(i.e. due to internal buffering in ffmpeg). On the s5p-mfc this causes
an infinite wait when polling to dequeue the buffers, which can be
prevented by increasing the total number of buffers. This commit adds a
warning when all the capture buffers are dequeued.
Reviewed-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Apparently the changes from 3c9185bf3a
aren't enough; even with that in place, I got errors like this
when trying to build for iOS:
src/libavdevice/avfoundation.m:135:5: error:
'AVCaptureDeviceTransportControlsPlaybackMode' is unavailable: not
available on iOS
AVCaptureDeviceTransportControlsPlaybackMode observed_mode;
^
The data of an AVPacket may be a part of the data of an AVBufferRef;
Therefore av_grow_packet() doesn't reallocate if the available space in
the actual buffer is sufficient for the enlargement. But given that it
also zeroes the padding it also needs to make sure that the buffer is
actually writable; this commit implements this.
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
hdsenc already had an explicit function to free all allocations in case
of an error, but it was not marked as deinit function, so that it was
not called automatically when the AVFormatContext for muxing gets freed.
Using an explicit deinit function also makes the code cleaner by
allowing to return immediately without "goto fail".
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
Enqueue/dequeue of the capture buffers should continue while draining.
Reference: linux/Documentation/media/uapi/v4l/dev-decoder.rst
"The client must continue to handle both queues independently,
similarly to normal decode operation. This includes:
...
- queuing and dequeuing CAPTURE buffers, until a buffer marked with
the V4L2_BUF_FLAG_LAST flag is dequeued"
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
The DNG code hardcodes plane 0 at some places, so its better to disallow cases
that have more planes.
Fixes: eg_crash
Found-by: 黄宁 <tsukimurarin@163.com>
Reviewed-by: Nick Renieris <velocityra@gmail.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
dng spec 1.5.0.0
"BitsPerSample
Supported values are from 8 to 32 bits/sample. The depth must be the same for each sample if
SamplesPerPixel is not equal to 1."
Fixes: eg_crash
Found-by: 黄宁 <tsukimurarin@163.com>
Reviewed-by: Nick Renieris <velocityra@gmail.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
"slice mode" option seems to be unnecessary since it could be
determined by -slices/max_nal_size.
default: SM_FIXEDSLCNUM_SLICE mode with cpu-number slices.
-slices N: SM_FIXEDSLCNUM_SLICE mode with N slices.
-max_nal_size: SM_SIZELIMITED_SLICE mode with limited size slices.
Add FF_API_OPENH264_SLICE_MODE macro to remove this option after
LIBAVCODEC_VERSION_MAJOR = 59.
Signed-off-by: Linjie Fu <linjie.fu@intel.com>
Signed-off-by: Martin Storsjö <martin@martin.st>
Libopenh264enc would set the slice according to the number of cpu cores
if uiSliceNum equals to 0 (auto) in SM_FIXEDSLCNUM_SLICE mode.
Prompt a warning for user to catch this.
Signed-off-by: Linjie Fu <linjie.fu@intel.com>
Signed-off-by: Martin Storsjö <martin@martin.st>
RC_BITRATE_MODE:
set BITS_EXCEEDED to iCurrentBitsLevel and allows QP adjust
in RcCalculatePictureQp().
RC_BUFFERBASED_MODE:
use buffer status to adjust the video quality.
RC_TIMESTAMP_MODE:
bit rate control based on timestamp, introduced in release 1.4.
Default to use RC_QUALITY_MODE.
Signed-off-by: Linjie Fu <linjie.fu@intel.com>
Signed-off-by: Martin Storsjö <martin@martin.st>
It would be 200kbps bitrate with gop size = 12 by default
which generated too many IDR frames in rather low bit rate.
The quality would be poor.
Set these default values to -1 to check whether it's specified
by user explicitly.
Use 2Mbps bitrate as nvenc sugguested, and leave gop size
untouched in libopenh264.
Signed-off-by: Linjie Fu <linjie.fu@intel.com>
Signed-off-by: Martin Storsjö <martin@martin.st>
Clip iMinQp/iMaxQp to (1, 51) for user specified qp range.
If not set, leave iMinQp/iMaxQp untouched and use the values (0, 51)
initialized in FillDefault(), and the QP range would be adjusted to the
defaults inside libopenh264 library according to the iUsageType, (12, 42)
for iUsageType == CAMERA_VIDEO_REAL_TIME which is default.
<https://github.com/cisco/openh264/blob/master/codec/encoder/core/src/encoder_ext.cpp#L375>
Signed-off-by: Linjie Fu <linjie.fu@intel.com>
Signed-off-by: Martin Storsjö <martin@martin.st>
Because not every user know about in_pad and out_pad reasonable value range
so maybe try to set 1.0, but setting 1.0 is so hugh to get an fatal error.
Suggested-by: Paul B Mahol <onemda@gmail.com>
Signed-off-by: Steven Liu <lq@chinaffmpeg.org>
The current implementation allows passing levels to libavcodec as
integers (such as "31" instead of "3.1").
However, in this case, the maximum reference frame value per level was
ignored because libavcodec converted the string to 310 instead of 31.
Since libx264 has correctly parsed the level to int
(x4->params.i_level_idc), we should rely on this value instead of
attempting to parse the level string on our own.
Signed-off-by: Josh Brewster <josh.brewster@protonmail.com>
Signed-off-by: Josh de Kock <josh@itanimul.li>
Without this setting, bitrate and qmin/qmax options have no
effect on the s5p-mfc hardware encoder.
Reviewed-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Currently the user gets unhelpful warnings when some default parameters
are not supported by the device. The verbosity of these log messages has
been changed to AV_LOG_DEBUG.
Reviewed-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
libswscale/vscale.c makes extensive use of function pointers and in
doing so it converts these function pointers to and from a pointer to
void. Yet this is actually against the C standard:
C90 only guarantees that one can convert a pointer to any incomplete
type or object type to void* and back with the result comparing equal
to the original which makes pointers to void generic pointers to
incomplete or object type. Yet C90 lacks a generic function pointer
type.
C99 additionally guarantees that a pointer to a function of one type may
be converted to a pointer to a function of another type with the result
and the original comparing equal when converting back.
This makes any function pointer type a generic function pointer type.
Yet even this does not make pointers to void generic function pointers.
Both GCC and Clang emit warnings for this when in pedantic mode.
This commit fixes this by using a union that can hold one member of any
of the required function pointer types to store the function pointer.
This works even for C90.
Reviewed-by: Michael Niedermayer <michael@niedermayer.cc>
Signed-off-by: Andreas Rheinhardt <andreas.rheinhardt@gmail.com>
Current muxers only use a single bitstream filter, so there is no need to
maintain code which operates on a list of bitstream filters. When multiple
bitstream filters are needed muxers can simply use a list bitstream filter.
If there is a use case in the future when different bitstream filters should be
added at subsequent packets then a new API possibly involving reconfiguring the
list bitstream filter can be added knowing the exact requirements.
Signed-off-by: Marton Balint <cus@passwd.hu>
