This adds a decoder for Broderbund's sprite-based QuickTime CDToons
codec, based on the decoder I wrote for ScummVM.
Signed-off-by: Alyssa Milburn <amilburn@zall.org>
Required minimal changes to the code so made sense to implement.
FFT and MDCT tested, the output of both was properly rounded.
Fun fact: the non-power-of-two fixed-point FFT and MDCT are the fastest ever
non-power-of-two fixed-point FFT and MDCT written.
This can replace the power of two integer MDCTs in aac and ac3 if the
MIPS optimizations are ported across.
Unfortunately the ac3 encoder uses a 16-bit fixed point forward transform,
unlike the encoder which uses a 32bit inverse transform, so some modifications
might be required there.
The 3-point FFT is somewhat less accurate than it otherwise could be,
having minor rounding errors with bigger transforms. However, this
could be improved later, and the way its currently written is the way one
would write assembly for it.
Similar rounding errors can also be found throughout the power of two FFTs
as well, though those are more difficult to correct.
Despite this, the integer transforms are more than accurate enough.
Compared to ad-hoc if(printed) ... code this allows the user to disable
it by adjusting the log level
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
In order for rate control to correctly allocate bitrate to each temporal
layer, correct temporal layer id has to be set to each frame. This
commit provides the ability to set correct temporal layer id for each
frame.
Signed-off-by: James Zern <jzern@google.com>
As we find ourselves wanting a way to transfer frames between
HW devices (or more realistically, between APIs on the same device),
it's desirable to have a way to describe the relationship. While
we could imagine introducing a `hwtransfer` filter, there is
almost no difference from `hwupload`. The main new feature we need
is a way to specify the target device. Having a single device
for the filter chain is obviously insufficient if we're dealing
with two devices.
So let's add a way to specify the upload target device, and if none
is specified, continue with the existing behaviour.
We must also correctly preserve the sw_format on such a transfer.
This commit adds the necessary code to initialize and use a Vulkan device
within the hwcontext libavutil framework.
Currently direct mapping to VAAPI and DRM frames is functional, and
transfers to CUDA and native frames are supported.
Lets hope the future Vulkan video decode extension fits well within this
framework.
Previously, the default palette would always be used.
Now, we can accept a custom palette, just like dvdsubdec does.
Signed-off-by: Michael Kuron <michael.kuron@gmail.com>
Signed-off-by: Michael Niedermayer <michael@niedermayer.cc>
This changes the separator character from comma to colon, but since this option
was only added recently I think it should be done for consistency with other
similar options.
Signed-off-by: Marton Balint <cus@passwd.hu>
This commit reuses the configuration options for VP8 that enables
temporal scalability for VP9. It also adds a way to enable three
preset temporal structures (refer to the documentation for more
detail) that can be used in offline encoding.
Signed-off-by: James Zern <jzern@google.com>
There was no consensus about separating AVExprState from AVExpr so here is a
minimal patch using the existing AVExpr to fix ticket #7528.
Signed-off-by: Marton Balint <cus@passwd.hu>
Reviewed-by: Michael Niedermayer <michael@niedermayer.cc>
Suggested-by: Hendrik Leppkes <h.leppkes@gmail.com>
Suggested-by: Nicolas George <george@nsup.org>
Signed-off-by: Steven Liu <lq@chinaffmpeg.org>
Adds support for the ADPCM variant used by some Argonaut Games' games,
such as 'Croc! Legend of the Gobbos', and 'Croc 2'.
Signed-off-by: Zane van Iperen <zane@zanevaniperen.com>
It is a common mistake that people only increase fifo_size when they experience
drops, unfortunately this does not help for higher bitrate (> 100 Mbps) streams
when the reader thread simply might not receive the packets in time (especially
under high CPU load) if the default 64 KB of kernel buffer size is used.
New default is determined so that common linux systems can set this buffer size
without tuning kernel parameters.
Signed-off-by: Marton Balint <cus@passwd.hu>
